manualshive.com logo in svg

JVC BR-DV6000, Instruction Manual, Page: 102 / 106

Share
Download
JVC BR-DV6000 Instruction Manual Download Page 102

102

OTHERS

– Installing SA-K46U RS-232C interface board –

The RS-422A REMOTE 1 terminal of BR-DV6000 can be replaced with SA-K46U RS-232C inter-
face board.  Use the plate for the RS-422A REMOTE 1 terminal for installing SA-K46U RS-232C
interface board.

The replacement procedure is described below.  However, to prevent electrical shock or injury, the
work should be performed only by a qualified personnel or a JVC authorized service agent.

Caution

To prevent electrical shock, remove the AC adaptor before install-
ing SA-K46U.

1.

Remove the RS-422A REMOTE 1 terminal.

1

Remove the two screws 

Å

 and pull out the RS-422A REMOTE

1 terminal.

2

Remove the connector cable connected to the connector of
the RS-422A REMOTE board.

❈

Remove the cable carefully not to damage it.

2.

Remove the plate of RS-422A REMOTE 1 terminal.

• For removing the plate, remove the two hexagonal screws first

with a tool such as a socket wrench.

3.

Remove the SA-K46U plate in the same procedure above.

4.

Fix the plate of RS-422A REMOTE 1 terminal, removed in 

2

above, to SA-K46U.

Hexagonal screws

The screw holes for the hexagonal screws are of the inch system.

5.

Install the SA-K46U.

1

Connect the connector cable with red wires to the connector of
the SA-K46U board.

Memo

BR-DV6000 connector cable colors
RS-232C: Red

RS-422A: Yellow

2

Fix SA-K46U to BR-DV6000 with the two screws 

Å

, removed

in 

1

- 

1

.

REMO

REMO

IN

OUT

MONITOR

OUT

PLAY

AUDIO

CH 1/3

CH 2/4

REMOTE 1

A

A

RS-422A REMOTE

Plate

Hexagon
screw

Socket wrench

Wire (Red)

Screw hole

SA-K46U

Plate

Plate

Hexagon screw

DV6000U_72-104_Eng.p65e

03/04/03, 3:11 PM

102

Summary of Contents for BR-DV6000











































































































Reviews:

No comments