JVC BR-D95U, Instructions Manual

Page: 67 / 76

132
13-2 RS-232C Commands
13 RS-232C protocol
TxD E9 3* 3* 3*
RxD 0A 0A 0A 0A
TxD EB 3*
RxD 0A 0A
Fifth byte (DATA3)
7 6 5 4 3 2 1
0
IS IS IS IS MON CF CF PB
CH2 1 CH2 0 CH1 1 CH1 0 /IPT SW FLD /EE
VIDEO INPUT SELECT
Setting
Bit name
VID GEN DIG VID LINE
CPN 0 0 0
LINE 0 0 1
SIF 0 1 —
Internal 1 — —
AUDIO INPUT SELECT
Setting
Bit name
IS**1 IS**2
ANA 0 0
AES/EBU 0 1
SDI 1 —
Internal 1 1
AUDIO MONITOR SELECT
Setting
Bit name
MS**L MS**R
OFF 0 0
R CH 0 1
L CH 1 0
L+R CH 1 1
COUNTER
Setting
Bit name
UB TC
CTL 0 0
TC — 1
UB 1 0
PB PB/EE
Setting
Bit name
PB/EE
PB/EE 0
PB 1
REMOTE
Setting
Bit name
Rem/9pin
REMOTE 1
LOCAL 0
Auxiliary commands
• [56: Clear] and [41: ClearError] are invalid.
• [40: Enter] is invalid.
E9: Edit Preset 2 Basic Table
Selects the Edit mode for 4 channels.
• Each bit is defined as follows:
7 6 5 4 3 2 1 0
First byte 0 0 1 1 0 INS ASM Video
Second byte 0 0 1 1 0 TC Aud2 Aud1
Third byte 0 0 1 1 DA4 DA3 DA2 DA1
Auxiliary commands
• [56: Clear] is valid for the second TxD byte or
later. All commands back to the first byte are
cleared.
• When [02: Error] occurs, [41: ClearError] is
valid. The previous command (one byte) is
cleared.
• [40: Enter] is invalid.
EB: TC Switch Preset Basic Table
Switches the time code generator function.
• Each bit is defined as follows:
7 6 5 4 3 2 1 0
The first byte 0 0 1 1 0 REC RUN REGEN EXT
• REC RUN : 1: Rec Run 0: Free Run
REGEN : 1: Regene 0: Preset
EXT : 1: Ext 0: Int
Auxiliary commands
• [56: Clear] is valid for the second TxD byte or later.
All commands back to the first byte are cleared.
• When [02: Error] occurs, [41: ClearError] is valid.
The previous command (one byte) is cleared.
• [40: Enter] is invalid.
EC: Panel Switch Preset JVC-1 Table
Switches various settings on the front panel.
• Settings are defined with the input values for the
second TxD byte or later. The bit assignment is
shown below.
Second byte (DATA0)
7 6 5 4 3 2 1 0
MS MS MS MS VID DIG LINE
CH4 L CH4 R CH3 L CH3 R GEN VID
Third byte (DATA1)
7 6 5 4 3 2 1 0
MS MS MS MS UB TC
CH2 L CH2 R CH1 L CH1 R
Fourth byte (DATA2)
7 6 5 4 3 2 1 0
IS IS IS IS Rem
CH4 1 CH4 0 CH3 1 CH3 0 /9pin
TxD EC ** ** ** **
RxD 0A 0A 0A 0A 0A
Setting
Bit name
MON/IPT
MONITOR 0
INPUT 1
AUDIO INPUT/AUDIO
MONITOR
Setting
Bit name
CF SW
CF OFF 0
CF ON 1
CF ON/OFF SW
Setting
Bit name
CF FLD
4 FIELD 0
8 FIELD 1
8 FIELD: (625) only
CF 4/8 SW
133
ED: Memory Switch Preset Basic/JVC-1 Table
Rewrites the contents of the menu switch.
• Refer to “Menu Switch Setting” to find out more
about menu switch contents.
• The setting of the menu switch changed with
this command is reset to the default setting
when the VCR is turned OFF.
• The second byte expresses the address
(Data0).
The corresponding addresses are as follows.
01 :Servo/System-1 information 08 :System-2 information
10 :System-3 information 20 :System-4 information
40 :System-5 information 88 :System-6 information
89 :System-7 information 90 :System-8 information
87 :System-9 information 09 :System-10 information
91 :System-11 information 92 :System-12 information
94 :System-14 information
0a :Video information-2
0b :Video information-3
0c :Video information-4 0d :Video-5 information
1b :Video-6 information 0e :Video-7 information
1e :Video-8 information 1c :Video-9 information
0f :Video-10 information 1f :Video-11 information
1d :Video-12 information 05 :Audio-2 information
06 :Audio-3 information 07 :Audio-4 information
03 :Audio-5 information 30 :Audio-6 information
31 :Audio-7 information 80 :TimeCode-1 information
81 :TimeCode-2 information 79 : TimeCode-3 information
77 :TimeCode-4 information 78 :TimeCode-5 information
82 :OnScreen-1 information 83 :OnScreen-2 information
84 :TBC information-1 86 :TBC information-3
• The third and fourth bytes express individual bit
information for the specified address. These are
expressed as Data1/Data2 information.
• The rewritten data can be checked with D3:
MemorySwitchSense. The D3 command
applies only to JVC Table-1.
Auxiliary commands
• When [02: Error] occurs, [56: Clear] is valid. All
commands back to the first TxD byte are cleared.
• When [02: Error] occurs, [41: ClearError] is valid.
The previous command (one byte) is cleared.
• [40: Enter] is invalid.
TxD ED ** ** **
RxD 0A 0A 0A 0A
13-2 RS-232C Commands
13 RS-232C protocol
TxD FB
RxD 0A
TxD FA
RxD 0A
TxD F7
RxD 0A
TxD F6
RxD 0A
F6: JVC Table-1 On Basic/JVC-1 Table
Use the JVC Table-1 commands.
F7: Basic Table On Basic/JVC-1 Table
Use the Basic Table commands.
JVC Table-1 is set to OFF.
FA: Rec/DubRequest Basic/JVC-1 Table
Send this command before sending commands
such as [CA: REC], [CB: RECPause].
• The recording standby mode is maintained until
the REC or STOP command or Error release
command is transmitted.
FB: VTR IND Basic/JVC-1 Table
Checks that a VCR is connected.