manualshive.com logo in svg

JVC AV-28KH1BUF, Service Manual

Share
Download
JVC AV-28KH1BUF Service Manual Download Page 13

(No.52139)1-13

4.6

ADJUSTMENT PROCEDURE

4.6.1 FOCUS / SCREEN ADJUSTMENT

4.6.2 AGC ADJUSTMENT

Item

Measuring 

instrument

Test point

Adjustment part

Description

FOCUS
adjustment

Signal 
generator

Remote 
control unit

FOCUS VR
[On the FBT]

(1) Receive a cross-hatch signal.
(2) Adjust FOCUS VR on the FBT as thin as possible. 

SCREEN
adjustment

Signal 
generator

Remote 
control unit

1pin (GND)
RGB cathodes
[CRT PWB]

SCREEN VR
[On the FBT]

(1) Receive a colour-bar signal.
(2) Ground pin of probe will be connected to 1pin (GND)

of the CRT socket.

(3) 1/100 oscilloscope probe to RGB cathodes on CRT

PWB.

(4) Adjust all control functions (brightness, colour and

contrast) to minimum settings.

(5) Adjust the SCREEN VR until acthode voltage

becomes 150V.

Item

Measuring 

instrument

Test point

Adjustment part

Description

AGC
adjustment

Signal 
generator

Remote 
control unit

Volt meter

AGC

(1) Receive a PAL BG signal at 60dBmV RF signal

level.

(2) Enter the SERVICE MENU.
(3) Press the [GREEN] key, then enter the VIDEO

adjustment group.

(4) Select AGC.
(5) Adjust AGC by pressing till voltage at pin 1 of

TUNER is equal to 3.0V.

(6) Press the [INFORMATION] key and memorize the

set value.

FBT

FOCUS VR

SCREEN VR

FBT

FOCUS VR

SCREEN VR

Summary of Contents for AV-28KH1BUF























Reviews:

No comments

Brands by name

Popular brands

Load more brands