JUNO JKI 2035 Operating Instructions Manual Download Page 6

17

t

Positioning the door shelves

To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
To make these adjustments proceed as follows:
Gradually pull the shelf in the direction of the arrows
until it comes free, then reposition as required.

For more thorough cleaning, the top door shelf can be
removed by pulling it in the direction of the arrows,
then refitting it in position.

Defrosting

Frost is automatically eliminated from the evaporator
of the refrigerator compartment every time the motor
compressor stops, during normal use.
The defrost water drains out through a trough into a
special container at the back of the appliance, over the
motor compressor, where it evaporates.

It is important to periodically clean the defrost
water drain hole in the middle of the refrigerator
compartment channel to prevent the water
overflowing and dripping onto the food inside. Use
the special cleaner provided, which you will find
already inserted into the drain hole.

D037

Unplug the appliance before carrying out any
maintenance operation.

Warning

This appliance contains hydrocarbons in its
cooling unit maintenance and recharging must
therefore only be carried out by authorised
technicians.

Periodic cleaning

Never use metal objects for clearing your appliance
as it may get damaged. Clean the inside with warm
water and bicarbonate of soda. Rinse and dry
thoroughly.

Periods of non-operation

When the appliance is not in use for long periods,
take the following precautions:
remove the plug from the wall socket;
remove all food:
defrost and clean the interior and all accessories;
leave the door ajar to allow air to circulate to prevent
unpleasant smells.

Interior light

The light bulb inside the refrigerator compartment can
be reached as follows:

1. unscrew the light cover securing screws;

2. unhook the moving part by pressing it as shown in 

the figure.

If the door is open and the light does not come on,
check that the bulb is properly screwed in; if it still
does not work, replace the bulb with one of the same
power.
The maximum rating is shown on the light cover.

MAINTENANCE

D411

CP1SIG

Summary of Contents for JKI 2035














Reviews: