manualshive.com logo in svg

Juniper SRX340, Hardware Manual

Share
Download
Juniper SRX340 Hardware Manual Download Page 21

CHAPTER 1

System Overview

•

SRX340 Services Gateway Description on page 3

•

SRX340 Services Gateway CLI and J-Web Access on page 3

SRX340 Services Gateway Description

The SRX340 Services Gateway consolidates security, routing, switching, and WAN
interfaces for midsize distributed enterprises. With advanced threat mitigation capabilities,
the services gateway provides cost-effective and secure connectivity across distributed
enterprises.

The SRX340 Services Gateway has a capacity of 3 gigabits per second (Gbps) and is 1
rack unit (U) tall. The services gateway has eight 1 G Ethernet ports, eight 1 G SFP ports,
one management port, 4 GB of DRAM memory, 8 GB of flash memory, and four
Mini-Physical Interface Module (Mini-PIM) slots.

The SRX340 Services Gateway runs the Junos operating system (Junos OS) and supports
the following features:

•

Firewall support with key features such as IPsec and VPN

•

Intrusion Detection and Prevention (IDP)

•

High availability

•

QoS

•

MPLS

Related

Documentation

SRX340 Services Gateway Chassis Overview on page 5

•

•

Understanding the SRX340 Services Gateway Front Panel on page 5

•

Understanding the SRX340 Services Gateway Back Panel on page 8

SRX340 Services Gateway CLI and J-Web Access

The SRX340 Services Gateway runs the Junos operating system (Junos OS). You can
use two user interfaces to monitor, configure, troubleshoot, and manage the services
gateway:

3

Copyright © 2016, Juniper Networks, Inc.

Summary of Contents for SRX340























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands