Juniper SRX340 Hardware Manual Download Page 138

Page: 138 / 150

inskränks genom att se till att det finns fritt utrymme på minst 15,2 cm omkring
ventilationsöppningarna.

Documentation

Battery-Handling Warning on page 115

•

Lightning Activity Warning on page 116

•

Jewelry Removal Warning on page 117

•

Product Disposal Warning on page 120

Product Disposal Warning

WARNING:

Disposal of this product must be handled according to all national

laws and regulations.

Waarschuwing

Dit produkt dient volgens alle landelijke wetten en

voorschriften te worden afgedankt.

Varoitus

Tämän tuotteen lopullisesta hävittämisestä tulee huolehtia kaikkia

valtakunnallisia lakeja ja säännöksiä noudattaen.

Attention

La mise au rebut définitive de ce produit doit être effectuée

conformément à toutes les lois et réglementations en vigueur.

Warnung

Dieses Produkt muß den geltenden Gesetzen und Vorschriften

entsprechend entsorgt werden.

Avvertenza

L'eliminazione finale di questo prodotto deve essere eseguita

osservando le normative italiane vigenti in materia

Advarsel

Endelig disponering av dette produktet må skje i henhold til nasjonale

lover og forskrifter.

Aviso

A descartagem final deste produto deverá ser efectuada de acordo

com os regulamentos e a legislação nacional.

¡Atención!

El desecho final de este producto debe realizarse según todas las

leyes y regulaciones nacionales

Varning!

Slutlig kassering av denna produkt bör skötas i enlighet med landets

alla lagar och föreskrifter.

Documentation

•

Battery-Handling Warning on page 115

•

Lightning Activity Warning on page 116

•

Jewelry Removal Warning on page 117

•

Operating Temperature Warning on page 118

120

SRX340 Services Gateway Hardware Guide

Summary of Contents for SRX340

























































































































Search results

Summary of Contents for SRX340

Reviews:

Brands by name

Popular brands

Juniper SRX340, Hardware Manual

Search results

Summary of Contents for SRX340

Reviews:

Brands by name

Popular brands