manualshive.com logo in svg

Juniper SRX320, Hardware Manual

Share
Download
Juniper SRX320 Hardware Manual Download Page 66

Related

Documentation

Preparing the SRX320 Services Gateway for Wall-Mount Installation on page 50

•

•

Preparing the SRX320 Services Gateway for Desk-Mount Installation on page 50

•

Installing the SRX320 Services Gateway in a Rack on page 53

Preparing the SRX320 Services Gateway for Wall-Mount Installation

You can mount an SRX320 Services Gateway on a wall. The four rubber feet attached
to the chassis provide stability. Before mounting the SRX320 Services Gateway on a wall:

•

Verify that the installation site meets the requirements described in

“Site Preparation

Checklist for the SRX320 Services Gateway” on page 20

.

•

Remove the services gateway chassis from the shipping carton. For unpacking
instructions, see

“Unpacking the SRX320 Services Gateway” on page 45

.

•

Verify that you have the following parts available in your wall-mounting kit:

•

Wall-mounting brackets

•

Screws

NOTE:

The wall-mounting kit is not shipped with the device and must be

ordered separately.

Related

Documentation

Preparing the SRX320 Services Gateway for Rack-Mount Installation on page 49

•

•

Installing the SRX320 Services Gateway on a Wall on page 57

Preparing the SRX320 Services Gateway for Desk-Mount Installation

You can mount an SRX320 Services Gateway on a desk or any other level surface
horizontally or vertically. The four rubber feet attached to the chassis provide stability.
Before mounting an SRX320 Services Gateway on a desk or other level surface:

•

Verify that the installation site meets the requirements described in

“Site Preparation

Checklist for the SRX320 Services Gateway” on page 20

.

•

Place the desk in its permanent location, allowing adequate clearance for airflow and
maintenance, and secure it to the building structure.

•

Remove the services gateway chassis from the shipping carton. For unpacking
instructions, see

“Unpacking the SRX320 Services Gateway” on page 45

.

Related

Documentation

Installing the SRX320 Services Gateway on a Desk on page 56

•

•

Preparing the SRX320 Services Gateway for Rack-Mount Installation on page 49

•

Preparing the SRX320 Services Gateway for Wall-Mount Installation on page 50

Copyright © 2016, Juniper Networks, Inc.

50

SRX320 Services Gateway Hardware Guide

Summary of Contents for SRX320



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands