Juniper SRX320 Hardware Manual Download Page 62

Page: 62 / 154

Documentation

Required Tools and Parts for Unpacking the SRX320 Services Gateway on page 45

•

Verifying Parts Received with the SRX320 Services Gateway on page 46

Verifying Parts Received with the SRX320 Services Gateway

The SRX320 Services Gateway shipment package contains a packing list. Check the
parts in the shipment against the items on the packing list. The packing list specifies the
part numbers and carries a brief description of each part in your order.

If any part is missing, contact a customer service representative.

A fully configured services gateway contains the chassis with installed components,
listed in

Table 14 on page 46

, and an accessory box, which contains the parts listed in

Table 15 on page 46

NOTE:

The parts shipped with your services gateway can vary depending on

the configuration you ordered.

Table 14: Parts List for a Fully Configured SRX320 Services Gateway

Quantity

Component

•

Non-PoE model

SRX320 Services Gateway chassis with six Gigabit Ethernet LAN ports, two 1 G
SFP ports, and two Mini-PIM slots.

•

PoE model

SRX320 Services Gateway chassis with six PoE ports, two 1 G SFP ports, and two
Mini-PIM slots.

CAT5E cable

DB9-to-RJ45 adapter

USB console cable with Type-A and Mini-B USB plugs

How to Set Up Your SRX320 Services Gateway

Power supply adapter and power cord

•

75 W, 12 V power supply adapter for non-PoE models

•

280 W, 54 V power supply adapter for PoE models

Table 15: Accessory/Upgrade Parts List for the SRX320 Services Gateway

Quantity

Part

Juniper Networks Product Warranty and RoHS Card

End User License Agreement

SRX320 Services Gateway Hardware Guide

Summary of Contents for SRX320





























































































































Search results

Summary of Contents for SRX320

Reviews:

Brands by name

Popular brands

Juniper SRX320, Hardware Manual

Search results

Summary of Contents for SRX320

Reviews:

Brands by name

Popular brands