Juniper SRX320 Hardware Manual Download Page 24

Page: 24 / 154

Table 4: SRX320 Services Gateway Front Panel LEDs

Description

Component

•

Solid amber (noncritical alarm)

•

Solid red (critical alarm)

•

Off (no alarms)

ALARM

•

Solid green (operating normally)

•

Solid red (error detected)

STAT

•

Solid green (receiving power)

•

Solid red (power failure)

•

Off (no power)

PWR

•

Solid green (all HA links are available)

•

Solid amber (some HA links are
unavailable)

•

Solid red (HA links are not functional)

•

Off (HA is disabled)

•

Solid green (Mini-PIM is functioning
normally)

•

Solid red (Mini-PIM hardware failure)

•

Off (Mini-PIM is not present or Mini-PIM is
not detected by the device)

mPIM0 and mPIM1

Documentation

SRX320 Services Gateway Chassis Overview on page 5

•

Understanding the SRX320 Services Gateway Back Panel on page 8

Understanding the SRX320 Services Gateway Back Panel

Figure 3 on page 8

shows the back panel of the SRX320 Services Gateway and

Table 5 on page 9

lists the components on the back panel.

Figure 3: SRX320 Services Gateway Back Panel

SRX320 Services Gateway Hardware Guide

Summary of Contents for SRX320





























































































































Search results

Summary of Contents for SRX320

Reviews:

Brands by name

Popular brands

Juniper SRX320, Hardware Manual

Search results

Summary of Contents for SRX320

Reviews:

Brands by name

Popular brands