background image

CHAPTER 27

Maintenance and Operational Safety
Guidelines and Warnings

Battery-Handling Warning on page 123

Lightning Activity Warning on page 124

Jewelry Removal Warning on page 125

Operating Temperature Warning on page 126

Product Disposal Warning on page 128

Battery-Handling Warning

WARNING:

Replacing the battery incorrectly might result in an explosion.

Replace the battery only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer's
instructions.

Waarschuwing

Er is ontploffingsgevaar als de batterij verkeerd vervangen

wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat
door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig
fabrieksvoorschriften weggeworpen te worden.

Varoitus

Räjähdyksen vaara, jos akku on vaihdettu väärään akkuun. Käytä

vaihtamiseen ainoastaan saman- tai vastaavantyyppistä akkua, joka on
valmistajan suosittelema. Hävitä käytetyt akut valmistajan ohjeiden mukaan.

Attention

Danger d'explosion si la pile n'est pas remplacée correctement.

Ne la remplacer que par une pile de type semblable ou équivalent,
recommandée par le fabricant. Jeter les piles usagées conformément aux
instructions du fabricant.

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr.

Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller
empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den
Anweisungen des Herstellers.

123

Copyright © 2016, Juniper Networks, Inc.

Summary of Contents for SRX320



























































































































































Reviews: