Juniper SRX320 Hardware Manual Download Page 111

Page: 111 / 154

CHAPTER 21

Overview of Replacing Components

•

Required Tools and Parts for Replacing the SRX320 Services Gateway
Components on page 95

•

SRX320 Services Gateway Field Replaceable Units Overview on page 95

Required Tools and Parts for Replacing the SRX320 Services Gateway Components

The following tools and parts are required for replacing a Mini-Physical Interface Module
(MPIM) on the services gateway:

•

Electrostatic bag or antistatic mat, for each component

•

Electrostatic discharge (ESD) grounding wrist strap

•

Flat-blade (–) screwdriver, approximately 1/8 in. (3 mm)

•

Phillips (+) screwdriver, number 1

•

Blank panels (if no component will be installed)

Documentation

Replacing Mini-Physical Interface Modules in the SRX320 Services Gateway on page 97

•

SRX320 Services Gateway Field Replaceable Units Overview

Field-replaceable units (FRUs) are components that you can replace at your site. The
Mini-Physical Interface Module (MPIM) is the only FRU on the SRX320 Services Gateway.

The Mini-PIMs are not hot-swappable. You must power off the services gateway before
removing or installing Mini-PIMs.

Documentation

•

Replacing Mini-Physical Interface Modules in the SRX320 Services Gateway on page 97

Summary of Contents for SRX320





























































































































Search results

Summary of Contents for SRX320

Reviews:

Brands by name

Popular brands

Juniper SRX320, Hardware Manual

Search results

Summary of Contents for SRX320

Reviews:

Brands by name

Popular brands