Juniper SRX320 Hardware Manual Download Page 101

Page: 101 / 154

CHAPTER 19

Maintaining Components

•

Required Tools and Parts for Maintaining the SRX320 Services Gateway Hardware
Components on page 85

•

Routine Maintenance Procedures for the SRX320 Services Gateway on page 85

•

Maintaining the SRX320 Services Gateway Cooling System Components on page 86

•

Maintaining the SRX320 Services Gateway Power Supply on page 86

Required Tools and Parts for Maintaining the SRX320 Services Gateway Hardware
Components

The following tools and parts are required to maintain the hardware components of the
services gateway:

•

Electrostatic bag or antistatic mat

•

Electrostatic discharge (ESD) grounding wrist strap

•

Flat-blade screw-blade screwdriver, approximately 1/8 in. (3 mm)

•

Phillips (+) screwdrivers, numbers 1 and 2

Documentation

Routine Maintenance Procedures for the SRX320 Services Gateway on page 85

•

Maintaining the SRX320 Services Gateway Cooling System Components on page 86

•

Maintaining the SRX320 Services Gateway Power Supply on page 86

Routine Maintenance Procedures for the SRX320 Services Gateway

For optimum performance of the services gateway, perform the following preventive
maintenance procedures regularly:

•

Inspect the installation site for moisture, loose wires or cables, and excessive dust.

•

Make sure that airflow is unobstructed around the device and into the air intake vents.

•

Check the status LEDs on the front panel of the services gateway and on the
Mini-Physical Interface Module (Mini-PIM) that you are using.

Summary of Contents for SRX320





























































































































Search results

Summary of Contents for SRX320

Reviews:

Brands by name

Popular brands

Juniper SRX320, Hardware Manual

Search results

Summary of Contents for SRX320

Reviews:

Brands by name

Popular brands