Juniper SRX1500 Hardware Manual Download Page 67

Page: 67 / 168

CHAPTER 12

Installing the Rack Mounting Hardware

•

Preparing the SRX1500 Services Gateway for Rack-Mount Installation on page 49

•

Connecting the SRX1500 Services Gateway to the Building Structure on page 50

Preparing the SRX1500 Services Gateway for Rack-Mount Installation

You can mount an SRX1500 Services Gateway on four-post (telco) racks, enclosed
cabinets, and open-frame racks. Center-mount racks are not supported.

Before mounting the SRX1500 Services Gateway in a rack:

•

Verify that the site meets the requirements described in

“Site Preparation Checklist

for the SRX1500 Services Gateway” on page 18

•

Verify that you have the following parts available in your rack-mounting kit for the
SRX1500 Services Gateway:

•

Rack-mounting brackets

•

Screws

•

Verify that the racks or cabinets meet the specific requirements described in

“SRX1500

Services Gateway Rack Requirements” on page 25

•

Place the rack or cabinet in its permanent location, allowing adequate clearance for
airflow and maintenance, and secure it to the building structure. For more information,
see

“SRX1500 Services Gateway Cabinet Airflow Requirements” on page 30

•

Remove the gateway chassis from the shipping carton. For unpacking instructions, see

“Unpacking the SRX1500 Services Gateway” on page 45

Documentation

Connecting the SRX1500 Services Gateway to the Building Structure on page 50

•

Unpacking the SRX1500 Services Gateway on page 45

•

Verifying Parts Received with the SRX1500 Services Gateway on page 46

Summary of Contents for SRX1500
















































































































































Search results

Summary of Contents for SRX1500

Reviews:

Related manuals for SRX1500

Brands by name

Popular brands

Juniper SRX1500, Hardware Manual

Search results

Summary of Contents for SRX1500

Reviews:

Related manuals for SRX1500

Brands by name

Popular brands