manualshive.com logo in svg

Juniper PTX5000, Hardware Manual

The Juniper PTX5000 is a high-performance networking device designed for large-scale data centers and service providers. To learn more about its features and specifications, you can download the free Hardware Manual from manualshive.com. This manual provides detailed instructions on how to operate and maintain your PTX5000.

Share
Download
background image

SEE ALSO

PTX5000 Craft Interface LEDs  |  23

PTX5000 Routing Engine Description

IN THIS SECTION

Routing Engine Slots  |  117

Routing Engine Functions  |  117

RE-DUO-C2600-16G Routing Engine Components  |  118

RE-PTX-X8-64G Routing Engine Components  |  120

RE-PTX-X8-128G Routing Engine Components  |  121

Routing Engine Boot Sequence  |  122

Routing Engine Slots

You can install one or two Routing Engines in the PTX5000. The Routing Engines install into the Control
Boards labeled CB0 and CB1. If two Routing Engines are installed, one functions as the primary and the
other acts as the backup. If the primary Routing Engine fails or is removed and the backup is configured
appropriately, the backup restarts and becomes the primary.

Routing Engine Functions

The Routing Engine handles all routing protocol processes, as well as the software processes that control
the PTX5000 router's interfaces, the chassis components, system management, and user access to the
PTX5000. The routing and software processes run on top of a kernel that interacts with the Packet
Forwarding Engine.

The Routing Engine constructs and maintains one or more routing tables. From the routing tables, the
Routing Engine derives a table of active routes, called the forwarding table, which is then copied into the
Packet Forwarding Engine. The design of the ASICs allows the forwarding table in the Packet Forwarding
Engine to be updated without interrupting forwarding performance.

The Routing Engine includes the following functions and features:

117

Summary of Contents for PTX5000


















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PTX5000

Lanner NCA-2510 Installation Manual preview
NCA-2510
Brand: Lanner Pages: 2
ZyXEL Communications P-660W-T1 v2 User Manual preview
P-660W-T1 v2
Brand: ZyXEL Communications Pages: 244
ETL TeleCLIENT TC7730 Series User Manual preview
TeleCLIENT TC7730 Series
Brand: ETL Pages: 83
NETGEAR RH328 Reference Manual preview
RH328
Brand: NETGEAR Pages: 142
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
QTech QSW-2900 User Manual preview
QSW-2900
Brand: QTech Pages: 406
ADIC FCR 200 Operator'S Manual preview
FCR 200
Brand: ADIC Pages: 140
Lantronix WP2002000-01 User Manual preview
WP2002000-01
Brand: Lantronix Pages: 75
Idis DR-2308P Quick Manual preview
DR-2308P
Brand: Idis Pages: 18
Paradyne iMarc SLV 9820-2M Installation Instructions Manual preview
iMarc SLV 9820-2M
Brand: Paradyne Pages: 24
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual preview
Acme Packet 3900
Brand: Oracle Pages: 70
HMS Anybus AWB3000 Startup Manual preview
Anybus AWB3000
Brand: HMS Pages: 18
WEIGL Nanotec Instruction Manual preview
Nanotec
Brand: WEIGL Pages: 6
Paradyne 1754 SHDSL Quick Installation Instructions preview
1754 SHDSL
Brand: Paradyne Pages: 1
Magnescale MG80-EI Operating Manual preview
MG80-EI
Brand: Magnescale Pages: 73
Infrapower PPS-03-S User Manual preview
PPS-03-S
Brand: Infrapower Pages: 36
TRENDnet TEW-635BRM - Wireless Router Quick Installation Manual preview
TEW-635BRM - Wireless Router
Brand: TRENDnet Pages: 13
Crestron DM-TX-200-C-2G Quick Start preview
DM-TX-200-C-2G
Brand: Crestron Pages: 4

Brands by name

Popular brands

Load more brands