background image

NOTE:

If a SIM card is installed in the second slot, then select the profile and configure the

radio access type for the secondary SIM card as well.

5. Configure the dialer interface:

Always-On mode:

user@host# set interfaces dl0 unit 0 family inet negotiate-address

user@host# set interfaces dl0 unit 0 family inet6 negotiate-address

user@host# set interfaces dl0 unit 0 dialer-options pool dialer-pool-number

user@host# set interfaces dl0 unit 0 dialer-options dial-string dial-number

user@host# set interfaces dl0 unit 0 dialer-options always-on

Dial-on-Demand mode:

user@host# set interfaces dl0 unit 0 family inet negotiate-address

user@host# set interfaces dl0 unit 0 family inet filter dialer dialer-filter-name

user@host# set interfaces dl0 unit 0 dialer-options pool dialer-pool-number

user@host# set interfaces dl0 unit 0 dialer-options dial-string dial-number

Backup mode:

user@host# set interfaces <interface-name> unit 0 backup-options interface dl0.0

user@host# set interfaces dl0 unit 0 dialer-options dial-string dial-number

6. Commit the configuration:

user@host# commit

SEE ALSO

Upgrading the Mini-PIM Firmware Using the CLI | 17

Upgrading the Modem Firmware Though Over-the-Air (OTA) | 20

Configuring a Static Route on the Dialer Interface

A static route enables the dialer interface to forward packets to a specific destination other than the default

route. Static routes are manually configured and entered into the routing table. You can configure a static

15

Summary of Contents for LTE Mini-PIM

































Reviews: