Jungheinrich EKE 20 b, Operating Instructions Manual

Page: 37 / 53

0402
.GB
E 14
5.4 Changing driving parameters
f
The driving behaviour of the truck is changed if the truck parameters are modified.
This is to be taken into consideration during start-up!
Parameters may only be modified with the truck parked and while it is not performing
any lifting movements.
– Commissioning the truck (refer section 3).
– Put the key into the key switch and turn it right until stop.
The operator menu is displayed for approx. 3 sec., indicating the truck designation.
Then, the current steering angle, the battery charging status and the operating hours
are indicated.
– Key Press selection menu key (26).
The indicator displays “acceleration” with the corresponding parameter.
– Proceed as indicated in the following diagram, if you want to check or modify any
truck parameters.
– Use the following keys to change between the adjustment parameters: (30) and
(24) and (25).
Acceleration
L
1)
Setting the time
XX:XX L
1)
Buzzer on/off
OFF L
1)
Low-speed ride
Load direction L
1)
Speed
Load direction L
1)
Low-speed ride
Direction of the driveL
1)
Speed
Direction of the driveL
1)
Reverse brake
L
3)
Coasting brake
L
1)
Acceleration
S
2)
Setting the time
XX:XX S
2)
Buzzer on/off
ON/OFF S
2
)
Low-speed ride
Load direction S
3)
Speed
Load direction S
2)
Low-speed ride
Direction of the drive S
3)
Speed
Direction of the drive S
2)
Reverse brake
S
3)
Coasting brake
S
2)
yes
Change?
no
BATT xxx% xx h
4)
1)
L = Read operating parameters (Read mode).
2)
S = Change operating parameters (Write mode) using the keys .
3)
no function
4
Indicator "Operating hours"
6)
Parameter selection indicator
5)
Indicator "Time“
7)
Change of parameters
BATT xxx% xx:xx
5)
Basic setting
Default val. for "driving“ L
3)
Basic setting
Default val. for "driving“ S
3
)
6)
7)
0402
.GB
E 14
5.4 Changing driving parameters
f
The driving behaviour of the truck is changed if the truck parameters are modified.
This is to be taken into consideration during start-up!
Parameters may only be modified with the truck parked and while it is not performing
any lifting movements.
– Commissioning the truck (refer section 3).
– Put the key into the key switch and turn it right until stop.
The operator menu is displayed for approx. 3 sec., indicating the truck designation.
Then, the current steering angle, the battery charging status and the operating hours
are indicated.
– Key Press selection menu key (26).
The indicator displays “acceleration” with the corresponding parameter.
– Proceed as indicated in the following diagram, if you want to check or modify any
truck parameters.
– Use the following keys to change between the adjustment parameters: (30) and
(24) and (25).
Acceleration
L
1)
Setting the time
XX:XX L
1)
Buzzer on/off
OFF L
1)
Low-speed ride
Load direction L
1)
Speed
Load direction L
1)
Low-speed ride
Direction of the driveL
1)
Speed
Direction of the driveL
1)
Reverse brake
L
3)
Coasting brake
L
1)
Acceleration
S
2)
Setting the time
XX:XX S
2)
Buzzer on/off
ON/OFF S
2
)
Low-speed ride
Load direction S
3)
Speed
Load direction S
2)
Low-speed ride
Direction of the drive S
3)
Speed
Direction of the drive S
2)
Reverse brake
S
3)
Coasting brake
S
2)
yes
Change?
no
BATT xxx% xx h
4)
1)
L = Read operating parameters (Read mode).
2)
S = Change operating parameters (Write mode) using the keys .
3)
no function
4
Indicator "Operating hours"
6)
Parameter selection indicator
5)
Indicator "Time“
7)
Change of parameters
BATT xxx% xx:xx
5)
Basic setting
Default val. for "driving“ L
3)
Basic setting
Default val. for "driving“ S
3
)
6)
7)