manualshive.com logo in svg

JUKI J-350QVP, Instruction Manual, Page: 25 / 32

Share
Download
JUKI J-350QVP Instruction Manual Download Page 25

– 24 –

<2. Sit-down type

>

②

Setting the Stitch Mode

・

  Cruise Stitch Mode

When you depress the foot controller, the machine will sew at

the minimum sewing speed that has been set.

When you move the material, the machine will sew

automatically with a sewing speed so that the set "Stitch per

Inch" (SPI) can be maintained.

・

  Baste Stitch Mode

When you depress the foot controller and move the material,

the machine will form stitches with the stitch pitch that has

been set.

・

Precise Stitch Mode

When you press the foot control

,

 the green light at JSS will

 

indicate machine is on.

When you begin to move the fabric the needle will move

 

creating a continuous even stitch. 

①

Setting the maximum

 Sewing Speed

You can set the maximum sewing speed in 5% increments.

・

  Manual Stitch Mode

When you depress the foot controller, the machine will sew at

the sewing speed that has been set.

* Non-regulated mode.  JSS does not function.

Summary of Contents for J-350QVP

































Reviews:

No comments