background image

– 7 –

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the 

following work after turning the power off and ascertaining that the motor is at rest.

4-4. Installing a bobbin

1.  Installing a bobbin

Firstly, fit a bobbin in the bobbin case. Draw the bobbin 

thread from the bobbin to the right. Then, pull the thread 

through threading openings 

 to 

.

After pulling out the bobbin thread, observe the bobbin from 

the bobbin side (not from the bobbin case side) to check 

whether or not the bobbin turns clockwise.

The bobbin thread tension can be adjusted with spring 

.

Open bobbin cap 

. Fit the hook in position.

In the case the feed dog base overlaps the bob-

bin case when the sewing machine stops, the 

bobbin case may not be removed smoothly.

In such a case, 

turn the hand-

wheel in the 

reverse direction 

and remove the 

bobbin case.

2.  Winding a bobbin

1)  Put a bobbin on bobbin winder shaft 

.

  At this time, align the spring of bobbin winder shaft 

 with 

groove 

 on this side.

2)  Pass the thread in the order of 

 to 

 and wind the 

thread on the bobbin.

3)  Bobbin winder frame 

 is set in position by pushing the 

bobbin.

4)  Run the sewing machine. Then, the bobbin rotates to au-

tomatically wind the thread on the bobbin.

5)  When the bobbin is fully wind with the thread, bobbin 

winder frame 

 comes off to stop automatically.

The amount of thread wound on a bobbin must be 80 % of 
the full capacity of the bobbin.

Standard amount of thread 

wound on a bobbin

80%

Loosen screw 

A

 of bobbin winder frame 

 and 

adjust the amount of thread wound on a bobbin 

by moving pin 

B

.

A

B

Summary of Contents for DU-1481 Series



































Reviews: