JUKI DU-1481 Series Instruction Manual Download

Page: 8 / 34

– 6 –

❶

❷

❸

❻

❾

❼

❽

❹

❺

❽

❼

❻

4-2. Threading the machine head

Thread the thread take-up lever and the relevant

parts as illustrated in the figure.

(Adequate)

Increase

Decrease

❶

❷

Needle thread

tension is ex-

cessively high
Needle thread

tension is ex-

cessively low

4-3. Adjusting the thread tension

1. Thread tension (needle thread)

The needle thread tension is increased by

turning thread tension screw

❶

clockwise or

decreased by turning it counterclockwise as

shown in the figure. Finished state of sewn

products varies depending on sewing condi-
tions such as the material, thread and stitch
length. It is therefore necessary to adjust the
thread tension appropriately according to the
sewing conditions.

2. Bobbin thread

Turn thread tension screw of the bobbin with

a screwdriver while fitting the screwdriver in

screw slot

❷

as shown in the figure. The thread

tension is increased by turning the thread ten-
sion screw with the screwdriver clockwise or
decreased by turning it counterclockwise.

Increase

WARNING :

To protect against possible personal injury due to abrupt start of the machine, be sure to start the

following work after turning the power off and ascertaining that the motor is at rest.

Summary of Contents for DU-1481 Series



































Search results

Summary of Contents for DU-1481 Series

Reviews:

Related manuals for DU-1481 Series

Brands by name

Popular brands

JUKI DU-1481 Series, Instruction Manual

Search results

Summary of Contents for DU-1481 Series

Reviews:

Related manuals for DU-1481 Series

Brands by name

Popular brands