JUKI AMS-210E-1306 Instruction Manual Download

Page: 64 / 128

– 60 –

(2) Sewing screen

Button and display

COMBINATION DATA NAME
display
THREAD CLAMP button

PRESSER DOWN button

RETURN TO ORIGIN button

COMBINATION DATA NO. display

PATTERN BUTTON NO. display

SEWING SHAPE display

SEWING ORDER RETURN
button
SEWING ORDER display

Description

Name which is inputted in the combination data being selected is displayed.

Effective/ineffective of thread clamp is selected.

: Thread clamp ineffective

: Thread clamp effective

Presser can be lowered and the presser down screen is displayed.
To raise the presser, press the presser up button displayed in the presser
down screen.

Presser can be returned to the start of sewing and is rasised at the time of
temporary stop.

Combination data No. being selected is displayed.

Pattern button No. being sewn is displayed.

Sewing shape which is registered to pattern button No. being sewn is
displayed.
Pattern to be sewn can be returned by one.

Sewing order being sewn at present is displayed.

Summary of Contents for AMS-210E-1306

































































































































Search results

Summary of Contents for AMS-210E-1306

Reviews:

Related manuals for AMS-210E-1306

Brands by name

Popular brands

JUKI AMS-210E-1306, Instruction Manual

Search results

Summary of Contents for AMS-210E-1306

Reviews:

Related manuals for AMS-210E-1306

Brands by name

Popular brands