Product ID: XB1-CHB
Expansion ports: 5
Dimensions: 125mm x 70mm x 22mm(including mounting tabs)
・
・
XB1-CHB
XBus Center Hub with Electronic Switch
XBus SERIES
DMSS 2.4GHz
Weight: 128g
・
・
・
XB1-PC4
(sold separately)
Connector (white)
for XBus port
XB1-PC4
PWM Converter
Serial Bus Communication System
MADE IN JAPAN
Deans ultra connecter
Deans ultra
connecter
Deans ultra
connecter
E s w i t c h a d a p t e r
Lead harness
(sold separately)
Power harness
(sold separately)
XB1-CV4
(sold separately)
XB1-CV1
(sold separately)
XB1-CV1
PWM Converter
Serial Bus Communication System
XB1-CV4
PWM Converter
Serial Bus Communication System
XB1-HB6
(sold separately)
Black case
XBus dedicated products
XBus dedicated products
XBus dedicated products
Do not use if the mounting is loose.
※Be sure to mount the XB1-CHB
to the model using the supplied
self tapping screws, rubber
grommets, and metal eyelets.
Be sure to use the supplied metal
eyelets and rubber grommets to
avoid vibration.
Metal eyelet
Self tapping screw
Grommet
If you have a large airplane using
numerous servos for aileron, elevator and
rudder, the XB1-CHB provides the perfect
solution. Power can be safely distributed
to high performance servos using
separate power cables (sold separately).
When also using PWM servos, we
strongly recommend using the XB1-CHB
unit together with the optional XB1-PC4
to provide the perfect control solution.
※The receiver batteries cannot be charged
via the XB1-CHB unit. Be sure to remove the
batteries before charging.
※Do not connect the power supply
directly to the receiver. Receiver power is
supplied from the XB1-CHB unit.
LED#1
LED#2
Specs
Connection Diagram for XBus Systems
JR XBus receiver
(sold separately)
Configuration
Features
●Be sure to mount the device securely to minimise vibration.
●Be sure to only connect this hub to a receiver's XBus port.
●Be sure to secure all loose wiring so vibration and flight loads
don't cause them to move.
※You can plug any device into any slot. There is no specific order.
※ It is not necessary fill up all the slots. The hub will work perfectly with empty slots.
Rx Battery
(sold separately)
Rx Battery
(sold separately)
Please refer to the following connecting diagram. The JR XBus system
allows you to use large numbers of servos and this heavy duty hub
ensures an adequate power supply is available.
Operating voltage: 4.5V 〜 8.5V
●Be sure the battery is fully charged before setting up the unit.
Low battery voltage may result in setup failure.
Connector for PWM servo
*This product is only for use with JR XBus system products.
To allow safe use, be certain to observe the following points.
■If you have further questions, please contact your local
dealer or JR distributor in your country.
Thank you for purchasing this JR product.
To allow correct and safe use of this
product, please read this operation
manual.
This logo indicates
products that support
the JR XBus System.
DANGER!
WARNING!
CAUTION!
● Do not use this product in the rain as water may cause electronic
devices to malfunction.
● Never disassemble or modify this product.
● Do not use this product in combination with other manufacturers
products such as servos, etc.
● Do not use this product if any of the wires or connectors are
damaged.
Not following this advice carries high risk of death or
serious injury to the user or third parties.
Not following this advice may result in death or serious
injury to the user or third parties.
Before use, check the following:
In order to prevent injury to the operator or third parties
(or damage to property), please observe the following
Not following this advice may cause injury to the user or third
party (or cause damage to property).
Operation Manual
Be sure to disconnect the battery from the hub between flying sessions. Leaving the
battery connected, even with the switch plug inserted, results in a small residual current
draw that will eventually flatten the receiver battery and potentially damage it.
ON/OFF Switch plug
＊Removing the switch plug
turns power ON.
Note: The plug is not sensitive
to insertion direction.
The XBus center hub with electric switch facilitates the connection of multiple servos,
batteries, XBus PWM converter harness, and XBus hub.
This product can be mounted using self tapping screws.
A dual power supply assures constant voltage to high current servos.
Built in electric switch (soft switch) provides greater safety.
Removing the switch jumper turns on the power.
●XB1-CHB/main unit ● Double ended male harness for receiver ● E switch adapter
● Switch plug ● Rubber grommets ● Metal eyelets ● Self tapping screws
● Operation manual (this document)
●
Note: When using batteries with
voltages above 6 volts, be sure to use
High Voltage or Wide Voltage servos.
Note: Please use two batteries of identical type and capacity (eg 2s LiPo's)
