Jøtul GI 545 DV MV Installation And Operation Instructions Manual Download Page 36

Page: 36 / 36

139919_GI 545 DV and DV MV 5/19

Ma
y 2019

139919

This appliance must be installed in conformance with local and national building regulations. Before

beginning the installation, it is important that the these instructions be carefully read and understood.

Jøtul maintains a policy of continuous product development. Consequently, products may differ in

specification, color or type of accessories from those illustrated or described in various publications.

Jøtul North America

55 Hutcherson Drive

Gorham, Maine 04038-2634

www.jotul.us

Your fireplace insert has a unique serial number imprinted on the rating plate which is

located in the valve compartment. Please record the serial number in the space below.
You may also wish to attach your purchase receipt to this manual for future reference.

MODEL: Jøtul GI

545

DV _____ Jøtul GI 545 DV MV _____

SERIAL NUMBER:_____________________________________

DATE OF PURCHASE:__________________________________

AUTHORIZED DEALER:_________________________________

ADDRESS __________________________________________

PHONE: ___________________________________________

INSTALLER:_____________________ DATE:______________

FUEL TYPE:__NG___________ LP____________

FUEL CONVERSION: NO _______ YES_____

NOTES:_____________________________________________

____________________________________________________

Summary of Contents for GI 545 DV MV





































Search results

Summary of Contents for GI 545 DV MV

Reviews:

Related manuals for GI 545 DV MV

Brands by name

Popular brands

Jøtul GI 545 DV MV, Installation And Operation Instructions Manual

Search results

Summary of Contents for GI 545 DV MV

Reviews:

Related manuals for GI 545 DV MV

Brands by name

Popular brands