Operating Instructions
NOTE: iPong should only be used with 40mm table tennis balls.
1. Place the assembled iPong V300 on the table, close to the back end and along the middle line. Then, angle
the projection hole to the desired left or right position on the table.
2. Before turning on the iPong, make sure that there are no table tennis balls inside the core engine. Rotate the
agitator manually so that the round gap in the agitator is not lined up with the ball entry hole. This will reduce
the possibility of jamming.
3. Dispense table tennis balls into the top assembly. 60-100 table tennis balls is the recommended amount.
4. Press the power button and play/pause button immediately after. This gives you time to adjust
each setting on the remote to your preferences. Then, press the play/pause button to start playing. Review the
instructions below on how to customize your settings.
Settings Customization
The iPong V300 uses an upper wheel and lower wheel to control ball spin, speed, and trajectory. When the
upper wheel spins faster than the lower wheel, topspin is generated. When the lower wheel spins faster than the
upper wheel, backspin is generated. When both wheels are spinning at the same speed, the ball is traveling across
the table with no spin.
Topspin Ball
BACKSPIN
4 0
7 3
4 0
3 7
Typical Master V300 setup for specific ball types:
Topspin balls:
TOPSPIN control between 5 and 7
BACKSPIN control between 2 and 4
Backspin balls:
TOPSPIN control between 2 and 4
BACKSPIN control between 5 and 7
BACKSPIN
4 0
7 3
4 0
3 7
Typical Master V300 setup for specific ball types:
Topspin balls:
TOPSPIN control between 5 and 7
BACKSPIN control between 2 and 4
Backspin balls:
TOPSPIN control between 2 and 4
BACKSPIN control between 5 and 7
Note: Due to varying conditions (ball size, dust, humidity, altitude, etc.), the remote control
settings provided for the iPong may not be exact. Adjust these settings to meet your desired need.
Backspin Ball
Settings Overview
Start with the iPong in pause mode . Using the plus buttons and minus buttons , adjust each
setting accordingly. For example: Frequency: “1” and Oscillation: “0”. (See below for Topspin and Backspin
settings.) Then press play/pause button to start .
Beginner topspin
:
This setup will create a slow topspin ball which is ideal for beginning players. First
set the robot 12” inward from the back edge of the table. Then set Topspin: “2” and Backspin: “1”.
Topspin Settings:
First set the iPong at back edge of table. Then set Topspin: “3” and Backspin: “1”. For
a stronger topspin, and increased distance, change these settings from 3:1 to 4:1, 5:1, 6:1, 7:1 or 8:1. If balls
are going o
ff
the table, decrease the Topspin setting accordingly.
Backspin Settings:
First set the iPong at back edge of table. Then set Topspin: “0” and Backspin: “6”. For
a stronger backspin, and increased distance, change the settings from 0:6 to 0:7 or 0:8. If balls are going o
ff
the table, decrease the Backspin setting accordingly.
The iPong Tilt Stand is a multi-tiered iPong el
-
evation tool, designed to change ball trajectory and
increase shot variation. Three heights are available:
9mm,17mm, or 26mm. The tilt stand is especially
useful when setting the iPong to shoot slow
balls, or fast backspin balls - that otherwise might
NOT go over the net. A bit of experimentation will
be required. With the tilt stand on the front of the
iPong, go up in elevation if balls go into the net.
increasing
.
increase
decreasing
decrease
4 0
7 3
4 0 6
2
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
up
in elevation if balls go into the net. And
go
down
in elevation if balls go off the table.
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For
fast backspin
balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on
rear
of
iPong.
Use for
very
fast
topspin
balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
Frequency Settings
Frequency is the rate at which table tennis
balls shoot out of the iPong. The higher the
Frequency setting, the greater the number of
balls shoot out per minute. “1” is the lowest
frequency while “8” is the highest frequency.
Oscillation (Side-To-Side) Settings
Oscillation is the setting used for shooting balls
to random locations on the table. The higher
the Oscillation setting, the faster the iPong
side-to-side motion. “1” is the slowest oscillation
while “8” is the fastest oscillation.
The Memory Function
The iPong V300 has the ability to save your
favorite settings. When you have your favorite
settings tuned on the iPong V300, press the
pause button on the remote, followed by
pressing the memory button.
When you want to recall your saved setting,
make sure you’re in play mode and press
the memory button. You’ll notice that iPong
V300 changes your saved settings. To change
your saved setting, repeat steps 1 and 2 above.
iPong Maintenance
t
After each use of the iPong, we suggest
you remove the power adaptor.
t
Clean the balls used in the iPong after
several uses. (Balls will collect dust on the
the iPong).
t
Wipe the iPong after several uses, and
put it back into the box (or a bag) to avoid
collecting dust.
t
Clean the wheels of iPong often! This is an
important step in maintaining this product.
Wet a clean cloth with water, or alcohol, and
wipe the wheels a few times by running the
cloth along the surface of the wheel.
t
Clean the motor under the agitator. First,
disassemble the horn, then pull the agitator
straight up lightly, to remove the agitator.
You will see dust or hair around the motor.
Carefully remove with a clean cloth.
t
Reinigen Sie oft die Räder des iPongs.
Dies ist ein wichtiger Schritt zur Erhaltung
der Funktionsfähigkeit. Benässen Sie ein
sauberes Tuch mit Wasser oder Alkohol
einige Male ab.
t
Reinigen Sie den Motor unter dem
Drehteller. Entfernen Sie zunächst den
Trichter, dann ziehen Sie den Drehteller
leicht nach oben um ihn zu entfernen.
Entfernen Sie den Schmutz sorgfältig mit
einem sauberen Tuch.
Erhebungs-Feature, entwickelt um Ballauswurf zu
Der iPong TILT STAND ist ein mehrstu
fi
ges iPong
ändern und Schlagvariationen zu erhöhen. Drei
Stufen sind verfügbar: 9mm, 17mm, 26mm. Der
TILT-STAND ist besonders nützlich bei langsamen
oder schnellen Backspin-Bällen - welche ohne diese
Funktion möglicherweise im Netz landen. Ein wenig
Experimentierfreude wird vorausgesetzt. Erhöhen
Sie den TILT-STAND an der Vorderseite des iPong,
wenn die Bälle ins Netz gehen und verringern Sie es,
wenn die Bälle hinter dem Tisch landen.
increasing
increase
decrease
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available:
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net.
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
go
down
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
Benutzung des TILT STAND
Frequenz-Einstellungen
Frequenz regelt die Ballauswurf-Geschwind-
igkeit des iPong. Je höher die Frequenz-Ein -
stellung, desto mehr Bälle werden pro Minute
ausgeworfen. “1” ist die niedrigste Frequenz, “8”
die höchste.
Oszillation (Seite-zu-Seite) Einstellungen
Memory-Funktion
Der iPong hat die Möglichkeit Ihre bevorzug -
ten Einstellungen zu speichern. Wenn Sie Ihre
bevorzugten Einstellungen vorgenommen
haben drücken Sie den Pause-Knopf auf
be
fi
ndet und drücken Sie Memory. Der iPong
der Fernbedienung, gefolgt vom Betätigen des
Memory-Knopfs. Wenn Sie Ihre gespeicherten
Einstellungen abrufen möchten, stellen Sie
sicher, dass sich das Gerät im Play-Modus
wechselt dann zu den gespeicherten Einstel-
lungen. Um Ihre gespeicherten Einstellungen zu
ändern, wiederholen Sie die Schritte 1 und 2.
Instandhaltung
t
Nach jeder Nutzung des iPongs
empfehlen wir den Netzstecker zu
entfernen.
t
Reinigen Sie die Bälle nach mehrfacher Be
-
nutzung. (Bälle werden staubig was die
Funktion des iPongs möglicherweise
t
Entstauben
-
DYs nach einer Benutzung. Lagern Sie
ihn im Karton (oder einer Tasche) um
Verstauben zu vermeiden
JOOLA Tischtennis GmbH & Co. KG
Wiesenstr. 1
t
76833 Siebeldingen
49 (0) 6345 - 9547-
t
www.joola.de
Quick Start Assembly instructions
Contents of the Box/Inhalt der Box/Contenu du carton/Con el iPong se incluye
A
A
D
A
C
D
A. Core Engine B. Agitator C. A/C Adapter D.Top/Bottom Assembly
E. Wireless Remote F. Tilt Stand
M
OSCILLATION
TOPSPIN
BACKSPIN
O
F
T
B
FREQUE NCY
iPong Motor iPong Drehteller iPong Netzteil
iPong Oberteil Unterteil
Kabellose Fernbedienung
Kippfuß
Moteur Assiette rotative Filetr Pièce dessus/dessous
Télécommande sans
fi
l
Réglage en hauteur
1x
1x
1x
2x
1x
1x
Motor Central Agitador A/C Adaptador
Piezas de montar (inferior/superior
）
Soporte Inclinable
Control Remoto Inalámbrico
Bedienungsanleitung
Bedienungsanleitung
HINWEIS: iPong sollte nur mit 40 mm iPong -Bällen benutzt werden.
1.
Platzieren Sie den zusammengebauten iPong auf dem Tisch nahe dem hinteren Ende sowie entlang der
Mittellinie. Danach richten Sie das Auswur
fl
och auf die gewünschte Position auf dem Tisch.
2.
“Stellen Sie sicher, dass sich keine Bälle im Motor be
fi
nden, wenn Sie den iPong in Betrieb nehmen.
Drehen Sie den Drehteller so, dass sich die Aussparung nicht über dem Balleingang be
fi
ndet.”
3.
Legen Sie die Bälle in das Oberteil. Die empfohlene Menge beträgt 60 - 100 Stück.
4.
Drücken Sie den Einschaltknopf und direkt danach Play/Pause. Dies gibt Ihnen Zeit, die richtigen
Einstellungen an der Fernbedienung auf Ihre Wünsche einzustellen. Danach drücken Sie wiederum Play/
Pause, um zu beginnen. Beachten Sie für Ihre individuellen Einstellungen untenstehende Hinweise.
Individuelle Einstellungen
Hinweis: Durch wechselnde Bedingungen (Ballgröße, Staub, Feuchtigkeit, Höhenlage usw.) können die Einstellungen
der Fernbedienung abweichen. Ändern Sie diese Einstellungen um das gewünschte Ergebnis zu erzielen.
Übersicht Einstellungen
Starten Sie den iPong im Pausenmodus. Benutzen Sie die Plus und Minus Taste um die
Einstellungen entsprechend zu ändern. Zum Beispiel: Frequenz „1“ und Oszillation „0“ (Topspin- und
Backspin-Einstellungen siehe unten). Drücken Sie danach Play/Pause, um zu beginnen.
Anfänger-Topspin:
Diese Einstellung erzeugt einen langsamen Topspin-Ball, der ideal für Anfänger ist.
Stellen Sie zuerst den iPong etwa 30cm vor der hinteren Tischkante auf. Dann nehmen Sie die Einstellungen
Topspin „2“ und Backspin „1“ vor.
Topspin-Einstellungen:
Stellen Sie den iPong zuerst an die hintere Tischkante. Stellen Sie dann
Topspin 3 und Backspin 1 ein. Für einen stärkeren Topspin und eine größere Entfernung, ändern Sie die
Einstellungen von 3:1 auf 4:1, 5:1, 6:1, 7:1 oder 8:1. Sollten die Bälle über den Tisch
fl
iegen, verringern Sie die
Topspin-Einstellung entsprechend.
Backspin-Einstellungen:
Stellen Sie den iPong zuerst an die hintere Tischkante. Stellen Sie dann
Topspin 0 und Backspin 6 ein. Für einen stärkeren Backspin und eine größere Entfernung ändern Sie die
Einstellungen von 0:6 auf 0:7 oder 0:8. Sollten die Bälle über den Tisch
fl
iegen, verringern Sie die
Backspin-Einstellung entsprechend.
1. Nehmen Sie die Teile aus der Box.
2. Setzen Sie den Drehteller mit dem Loch auf den Plastikstab auf der Oberseite
des Motors und drücken Sie bis zum Einrasten.
3. Setzen Sie den Motor mit den Löchern auf das Unterteil und drehen ihn bis
zum Einrasten.
4. Setzen Sie den Motor mit den Löchern auf das Oberteil und drehen ihn bis
zum Einrasten.
5. Schließen Sie den Netzstecker hinten am Motor an und verbinden Sie ihn mit
der Steckdose.
OPERATIONS MANUAL
iPong
USING THE iPong TILT STAND
FAQ/Troubleshooting Tips
Balls are loaded but agitator is not moving?
- Remove some of the balls from the top assembly.
Overloading the top with balls may be too heavy for the
agitator to rotate.
Balls getting jammed?
- Be sure you are using the correct sized balls. iPong
robots work only with 40mm table tennis balls, and
work best with plastic table tennis balls.
- The maximum ball capacity of the top assembly is 100
balls. 60-100 table tennis balls is the recommended
amount.
- If the round gap on the agitator stops directly above the
ball entry hole, multiple balls could enter into the core
engine at once and stall. To prevent this, avoid turning
gap aligned.
Balls getting jammed immediately after reloading?
- This is often caused by the Topspin and/or Backspin set-
engine and top assembly. Let the iPong run empty,
making sure that the Topspin and Backspin settings are
set to “1” or higher. Then, reload the balls while the
iPong is running.
A ball is jammed or stuck inside the iPong?
-
ball out. You can also tip the unit upside down and
Unplug the iPong. Manually reach in and
fi
sh the
shake it gently to get the ball to fall out.
Agitator tab broken?
- The agitator is a sensitive part and can break if the
iPong is not handled carefully. Once the agitator is
service for a replacement part.
Core engine is very loud?
-
tions in the wheel motors. Also, check that iPong is
Power o
ff
the iPong and examine for any obstruc-
on a level surface to prevent the motors from vibrating
and moving around.
Last few balls in the top assembly aren’t shooting out?
-This is an indicator that it is time to reload the balls.
Does the iPong require any maintenance?
- It does not require any maintenance, although it is
important to make sure the wheels are clean and free
from dust, hair, and pet dander.
- Try our Table Tennis Ball Catch Net or Table Tennis Ball
Pickup Net to make collecting balls faster and easier.
Available at www.ipong.de under Accessories.
If your problem or question isn’t helped by any of these
ipong.de
Having trouble with Topspin/Backspin settings?
- Remember that when the Topspin and Backspin set-
tings are the same, no spin is generated on the ball.
- Check the Settings Customization in the beginning
of the user guide.
iPong won’t turn on?
-Check to see that the A/C adapter is plugged in all
the way.
Core engine not running?
-Check to see that the A/C adapter is plugged in all
the way.
-
there are obstructions (dust, hair, pet dander, etc.)
keeping the motor from spinning. Remove any
obstructions, re-plug A/C adapter and try again.
Rubber wheels not spinning?
-Check to see that the A/C adapter is plugged in all
the way.
- Unplug A/C adapter. Remove top and bottom as-
sembly. Remove front plastic casing by pressing the
top and bottom tabs. Check to see if there are any
obstructions (dust, hair, pet dander, etc.) keeping the
rubber wheels from spinning. Remove any obstruc-
tions, re-plug A/C adapter and try again.
Balls hitting the side of the projection hole?
-Be sure you are using the correct sized balls.
iPong robots work only with 40mm table tennis balls,
and work best with plastic table tennis balls.
Balls falling out of projection hole, not shooting?
- Be sure you are using the correct sized balls.
iPong robots work only with 40mm table tennis
balls, and work best with plastic table tennis balls.
- Be sure you are using the correct sized balls.
iPong robots work only with 40mm table tennis
balls, and work best with plastic table tennis balls.
Balls not shooting at a consistent speed?
-Check to see that the A/C adapter is plugged in all
the way.
- Be sure you are using the correct sized balls.
iPong robots work only with 40mm table tennis
balls, and work best with plastic table tennis balls.
-Try moving the iPong further back, closer to the
edge of the table.
- Decrease the Backspin setting and/or increase the
Topspin setting incrementally and test until the balls
start hitting the table again.
increasing
.
increase
decreasing
decrease
4 0
7 3
4 0 6
2
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
up
in elevation if balls go into the net. And
go
down
in elevation if balls go off the table.
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For
fast backspin
balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on
rear
of
iPong.
Use for
very
fast
topspin
balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
increasing
.
increase
decreasing
decrease
4 0
7 3
4 0 6
2
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
up
in elevation if balls go into the net. And
go
down
in elevation if balls go off the table.
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For
fast backspin
balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on
rear
of
iPong.
Use for
very
fast
topspin
balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
increasing
.
increase
decreasing
decrease
4 0
7 3
4 0 6
2
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
up
in elevation if balls go into the net. And
go
down
in elevation if balls go off the table.
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For
fast backspin
balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on
rear
of
iPong.
Use for
very
fast
topspin
balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
increasing
.
increase
decreasing
decrease
4 0
7 3
4 0 6
2
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
up
in elevation if balls go into the net. And
go
down
in elevation if balls go off the table.
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For
fast backspin
balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on
rear
of
iPong.
Use for
very
fast
topspin
balls.
Position iPong near end of table - OR
in middle of table! Start in lowest iPong
position, and adjust upward as needed.
increasing
.
increase
decreasing
decrease
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available:
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net.
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
up
in elevation if balls go into the net. And
go
down
in elevation if balls go off the table.
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For
fast backspin
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
iPong.
Position iPong near end of table -
in middle of table! Start in lowest
position, and adjust upward as needed.
iPong
increasing
.
increase
decreasing
decrease
4 0
7 3
4 0 6
2
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
up
in elevation if balls go into the net. And
go
down
in elevation if balls go off the table.
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For
fast backspin
balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on
rear
of
iPong.
Use for
very
fast
topspin
balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
iPong
increasing
.
increase
decreasing
decrease
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm.
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net.
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
up
in elevation if balls go into the net. And
go
down
in elevation if balls go off the table.
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For
fast backspin
balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on
iPong.
Use for
Position iPong near end of table -
in middle of table! Start in lowest
position, and adjust upward as needed.
increasing
.
increase
decreasing
decrease
4 0
7 3
4 0 6
2
Using the iPong
Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front
of the iPong, go
up
in elevation if balls go into the net. And
go
down
in elevation if balls go off the table.
V300 control adjustments for ball errors
For
slower
balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For
fast backspin
balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on
rear
of
iPong.
Use for
very
fast
topspin
balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
iPong
iPong
iPong
Für langsamere Bälle positionieren Sie den iPong in der
Nähe der Tischmitte. Stellen Sie die Neigung auf die
niedrigste Stufe und passen diese bei Bedarf an. Nutzen Sie
dafür den Untersteller.
Für schnelle Backspin-Bälle positionieren Sie den iPong am
Ende des Tisches. Stellen Sie die Neigung auf die niedrigste
Stufe und passen diese bei Bedarf an. Nutzen Sie dafür den
Untersteller.
Fortgeschritten: Platzieren Sie den Untersteller an die
Rückseite des iPong. Erzeugt sehr schnelle Topspin-Bälle.
Positionieren Sie den iPong am Ende des Tisches oder in
der Mitte! Starten Sie in der niedrigsten Stufe und erhöhen
Sie falls benötigt.
1. Remove all contents from the box.
2. Attach the Agitator (B) to the top of the Core Engine (A) by aligning the plastic rod
on the Core Engine (A) to the hole on the bottom of the Agitator (B) and pressing
down until secure.
3. Align the tabs on the Bottom Assembly (D) to the slots at the bottom of the Core
Engine (A). Insert and turn clockwise to lock.
4. Align the tabs on the Top Assembly (D) to the slots at the top of the Core Engine
(A). Insert and turn clockwise to lock.
5. Before plugging into the electric outlet, insert the A/C Adapter (C) into the back of
the Core Engine (A).
Der iPong benutzt ein oberes und unteres Rad, um Ballspin, Geschwindigkeit und Auswurf zu kontrolieren. Wenn sich das
obere Rad schneller als das untere dreht wird Topspin erzeugt. Wenn sich das untere Rad schneller als das obere dreht,
wird Backspin erzeugt. Wenn sich beide Räder mit der gleichen Geschwindigkeit drehen wird der Ball ohne Spin
ausgeworfen.
Oszillations-Einstellungen werden benutzt, um
Bälle auf verschiedene Bereiche des Tisches zu
werfen. Je höher die Oszillation-Einstellung,
desto schneller vollzieht der iPong die
"Seite-zu-Seite Bewegung". “1” ist die langsamste
Bewegung, 8 die schnellste Oszillation.
B
tings starting at “0” when
fi
rst turning on the iPong.
Turn o
ff
the iPong and remove all balls from the core
