background image

32 – 

English

Lubrication

Checking the engine’s oil level.

Check the oil level in the engine when the Rider stands 
horizontal with the engine switched off.

Open the engine cover.

Loosen the dipstick, pull it up and wipe it off.

The dipstick should be 

completely screwed down

Pull the dipstick out again and read the oil level.

The oil level should be between the markings on the dipstick. 
If the level is approaching the ADD mark, top up the oil to the 
FULL mark on the dipstick.

The oil is topped up through the hole the dipstick sits in.

Fill the oil slowly. Tighten the dipstick correctly before starting 
the engine. Start and run the engine at idling speed for 
approx. 30 seconds. Turn off the engine. Wait 30 seconds and 
check the oil level. If necessary fill so that the oil comes up to 
the FULL mark on the dipstick.

First and foremost use synthetic engine oil class SJ-CF 5W/
30 or 10W/30 for all temperature ranges. Mineral oil SAE30, 
class SF–CC can be used at temperatures > +5 

°

C (40 

°

F)

Do not mix different types of oil.

Replacing the engine oil

The engine oil should be changed the first time after 5 hours 
running time. It should then be changed after every 50 hours 
of running time.

When operating with a heavy load or at high ambient 
temperatures, replace every 25 hours.

1

Place a container underneath the engine’s left oil drain 
plug.

2

Remove the dipstick. Remove the drain plug from the 
engine’s left side.

3

Let the oil run out into the container.

4

Fit the drain plug and tighten it.

5

Fill with oil up to the ”FULL” mark on the dipstick The oil is 
topped up through the hole the dipstick sits in. See 
Checking the engine’s oil level for filling instructions.

The engine holds 1.5 litres (1.6 USqt) when the oil filter is 
not replaced and 1.7 litres (1.8 USqt) of oil when the oil 
filter is replaced.

6

Run the engine warm, then check that there is no leakage 
from the oil plug.

ADD

FULL

ADD

FULL

!

WARNING! Engine oil can be very hot if it is 
drained directly after stopping the engine. 
Allow the engine to cool somewhat first.

IMPORTANT INFORMATION

Used engine oil is a health hazard and must not be 
disposed of on the ground or in nature; it should always be 
disposed of at a workshop or appropriate disposal location. 
Avoid skin contact; wash with soap and water in case of 
spills.

Summary of Contents for FR 2216 A 4X4









































Reviews: