manualshive.com logo in svg

Jonsered CS 2152 EPA III, Operator'S Manual

Introducing the Jonsered CS 2152 EPA III, a high-performance chainsaw perfect for professionals and homeowners alike. Unlock the full potential of this reliable tool by downloading the Operator's Manual for free from our website. Discover enhanced safety features, maintenance details, and operating instructions to maximize your cutting experience.

Share
Download
background image

 

GENERAL SAFETY PRECA

 

UTIONS

 

English

 

 –

 

 

 

7

 

Bef

 

ore using a new chain saw

 

•

 

Please read this manual carefully.

•

Check that the cutting equipment is correctly fitted 
and adjusted. See instructions under the heading 
Assembly.

•

Refuel and start the chain saw. See the instructions 
under the headings Fuel Handling and Starting and 
Stopping.

•

Do not use the chain saw until sufficient chain oil has 
reached the chain. See instructions under the 
heading Lubricating cutting equipment.

•

Long-term exposure to noise can result in permanent 
hearing impairment. So always use approved hearing 
protection.

 

Impor

 

tant

Always use common sense

 

It is not possib

 

le to cover every conceivable situation you 

can face when using a chain saw. Always exercise care 
and use your common sense. Avoid all situations which 
you consider to be beyond your capability.  If you still feel 
uncertain about operating procedures after reading these 
instructions, you should consult an expert before 
continuing. Do not hesitate to contact your dealer or us if 
you have any questions about the use of the chain saw. 
We will willingly be of service and provide you with advice 
as well as help you to use your chain saw both efficiently 
and safely. Attend a training course in chain saw usage if 
possible. Your dealer, forestry school or your library can 

!

 

W

 

ARNING! Under no circumstances may 

the design of the machine be modified 
without the permission of the 
manufacturer. Always use genuine 
accessories. Non-authorized 
modifications and/or accessories can 
result in serious personal injury or the 
death of the operator or others. Your 
warranty may not  cover damage or 
liability caused by the use of non-
authorized accessories or replacement 
parts.

!

 

W

 

ARNING! A chain saw is a dangerous 

tool if used carelessly or incorrectly and 
can cause serious, even fatal injuries. It 
is very important that you read and 
understand the contents of this 
operator’s manual.

!

 

W

 

ARNING! The inside of the muffler 

contain chemicals that may be 
carcinogenic. Avoid contact with these 
elements in the event of a damaged 
muffler.

!

 

W

 

ARNING! Long term inhalation of the 

engine’s exhaust fumes, chain oil mist 
and dust from sawdust can represent a 
health risk.

!

 

W

 

ARNING! The ignition system of this 

machine produces an electromagnetic 
field during operation. This field may 
under some circumstances interfere with 
pacemakers. To reduce the risk of 
serious or fatal injury, we recommend 
persons with pacemakers to consult 
their physician and the pacemaker 
manufacturer before operating this 
machine.

 

IMPOR

 

TANT!

The machine is only designed for cutting wood.

You should only use the saw with the bar and chain 
combinations we recommend in the chapter Technical 
data.

Never use the machine if you are fatigued, while under 
the influence of alcohol or drugs, medication or anything 
that could affect your vision, alertness, coordination or 
judgement. 

Wear personal protective equipment. See instructions 
under the heading Personal protective equipment.

Do not modify this product or use it if it appears to have 
been modified by others.

Never use a machine that is faulty. Carry out the checks, 
maintenance and service instructions described in this 
manual. Some maintenance and service measures 
must be carried out by trained and qualified specialists. 
See instructions under the heading Maintenance.

Never use any accessories other than those 
recommended in this manual. See instructions under 
the headings Cutting equipment and Technical data.

CAUTION! Always wear protective glasses or a face 
visor to reduce the risk of injury from thrown objects. A 
chain saw is capable of throwing objects, such as wood 
chips, small pieces of wood, etc, at great force. This can 
result in serious injury, especially to the eyes.

!

 

W

 

ARNING! Running an engine in a 

confined or badly ventilated area can 
result in death due to asphyxiation or 
carbon monoxide poisoning.

!

 

W

 

ARNING! Faulty cutting equipment or 

the wrong combination of bar and saw 
chain increases the risk of kickback! 
Only use the bar/saw chain combinations 
we recommend, and follow the filing 
instructions. See instructions under the 
heading Technical  data.

Summary of Contents for CS 2152 EPA III













































Reviews:

No comments

Related manuals for CS 2152 EPA III

ICS 603GC Operator'S Manual preview
603GC
Brand: ICS Pages: 26
Narex EPR 30-20 Instructions For Use Manual preview
EPR 30-20
Brand: Narex Pages: 44
Zenoah G621AVS Owner'S Manual preview
G621AVS
Brand: Zenoah Pages: 48
Zenoah G4200 Owner'S Manual preview
G4200
Brand: Zenoah Pages: 58
Zenoah G3800 Service Parts List preview
G3800
Brand: Zenoah Pages: 4
Zenoah G2500 Owner'S Manual preview
G2500
Brand: Zenoah Pages: 19
Defort 98291865 User Manual preview
98291865
Brand: Defort Pages: 100
Titan TTL650GDO Safety And Operating Manual preview
TTL650GDO
Brand: Titan Pages: 27
YATO YT-84905 Manual preview
YT-84905
Brand: YATO Pages: 96
Dolmar PS-35 C Repair Manual preview
PS-35 C
Brand: Dolmar Pages: 28
Dolmar AS-1212LG Instruction Manual preview
AS-1212LG
Brand: Dolmar Pages: 76
Sparky Group TV 1835 Original Instructions Manual preview
TV 1835
Brand: Sparky Group Pages: 151
Echo DCS-2500T Operator'S Manual preview
DCS-2500T
Brand: Echo Pages: 200
RADLEY YFG52-H Owner'S Manual preview
YFG52-H
Brand: RADLEY Pages: 30
Makita DUC256PG2 Instruction Manual preview
DUC256PG2
Brand: Makita Pages: 24
Craftsman 358.350461 Instruction Manual preview
358.350461
Brand: Craftsman Pages: 22
DuroStar DS5018CS Owner'S Manual preview
DS5018CS
Brand: DuroStar Pages: 20
Benchmark 5240-050 Manual preview
5240-050
Brand: Benchmark Pages: 32

Brands by name

Popular brands

Load more brands