English
– 25
MAINTENANCE
Fine adjustment of the idle speed T
Adjust the idle speed using the idle adjustment screw T, if it is
necessary to readjust. First turn the idle adjustment screw T
clockwise until the cutting attachment starts to rotate. Then
turn the screw anticlockwise until the cutting attachment
stops. The idle speed is correctly adjusted when the engine
will run smoothly in every position. The idle speed should also
be well below the speed at which the cutting attachment starts
to rotate.
High speed jet H
Note that the engine should not be under load when you
adjust the high speed jet H. You should therefore remove the
cutting attachment, nut, support flange and drive disc before
adjusting the high speed jet H. The high speed jet H affects
the engine power, speed, temperature and fuel consumption.
If the high speed jet H is set too lean (screwed in too far) the
engine speed will be too high and cause engine damage. Do
not let the engine run at full speed for more than 10 seconds.
Apply full throttle and turn the high speed jet H very slowly
clockwise until the engine slows down. Then turn the high
speed jet H very slowly anticlockwise until the engine starts to
run unevenly. Now turn the high speed jet H slowly clockwise
a little way until the engine runs smoothly.
The high speed jet H is adjusted correctly when the machine
burbles a little. If the machine races then the setting is too
lean. If the engine produces a lot of smoke and burbles a lot
then the setting is too rich.
CAUTION!
For optimum adjustment of the carburettor,
contact a qualified dealer/service workshop that has a
revolution counter at their disposal.
Correctly adjusted carburetor
When the carburetor is correctly adjusted the machine will
accelerate without hesitation and burble a little at maximum
speed. It is also important that the cutting attachment does
not rotate at idle. If the low speed jet L is set too lean it may
cause starting difficulties and poor acceleration.
If the high speed jet H is set too lean it will result in less power,
less performance, poor acceleration and/or damage to the
engine.
If both the L and H jets are set too rich it will results in
acceleration problems or too low a working speed.
Adjusting the start throttle speed
The correct start throttle speed is set by means of an adjuster
on the rear of the handle next to the cable. Use this screw (4
mm Allen screw) to increase or decrease the start throttle
speed.
Proceed as follows:
1
Run the machine at idle.
2
Press the start throttle lock as described under the
heading Starting and stopping.
3
If the start throttle speed is too low (below 4000 rpm), turn
the adjuster screw A clockwise until the cutting
attachment starts to rotate. Then turn A clockwise a
further 1/2 turn.
4
If the start throttle speed is too high, turn the adjuster
screw A anticlockwise until the cutting attachment stops.
Then turn adjuster screw A clockwise a further 1/2 turn.
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
H
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
5 mm
Summary of Contents for BC 2125
