JOMAR AEP-100 Installation, Operation & Maintenance Instructions Manual Download Page 2

Page: 2 / 13

040215

Jomar Valve ・ 7243 Miller Drive, Warren, MI 48092 ・ www.jomarvalve.com ・ phone: (586) 268-1220 ・ fax: (586) 979-8315

Note: Information subject to change without notice.

IMPORTANT

Please read the installation operation and maintenance instruction prior

to using any Jomar Valve component. Failure to follow the instructions

may damage the component and/or void the warranty.

Contents

General

Features

Specifications

Ordering

Inside View

Principle of Operation

Block Diagram of AEP-100

Installation

Example of attaching to actuator

Connection with feedback shaft

Cam attaching procedure

Attaching procedure of opening degree indication plate

Air Piping Connection

Electrical Wiring

Adjustment

Zero Adjustment

Span Adjustment

Auto/Manual Switch

Seat Adjuster (sensitivity adjustment)

Maintenance And Check

Caution On Handling

Trouble Shooting

Option

Pilot valve with output orifice

Summary of Contents for AEP-100














Search results

Summary of Contents for AEP-100

Reviews:

Related manuals for AEP-100

Brands by name

Popular brands

JOMAR AEP-100, Installation, Operation & Maintenance Instructions Manual

Search results

Summary of Contents for AEP-100

Reviews:

Related manuals for AEP-100

Brands by name

Popular brands