manualshive.com logo in svg

Johnson Matthey Tracerco PED Blue, User Manual, Page: 22 / 25

Share
Download
Johnson Matthey Tracerco PED Blue User Manual Download Page 22

 

 

 

MN1010 Rev. G 

22 of 25 

 

 

4 

Maintenance 

Attention

: The PED-IS is certified for use in potentially explosive atmospheres (hazardous areas). Therefore, the 

PED-IS must be operated in accordance with the information contained in the document MN1004 Essential Safety 
Information. The PED-IS must never be used in a hazardous area whilst connected via USB as this would violate the 
certification and may create an unsafe situation.  

4.1 

Upgrading the firmware 

Firmware  upgrades  to  PEDs can  be  download  from  the  Tracerco  website  (

www.tracerco.com/monitors

)  and  then 

installed using 

DoseVision™. 

4.2 

Charing the battery 

The PED-IS must be charged using a charger dock.  

 

Warning 

The PED-IS must never be used in a hazardous area whilst connected via USB as this would 
violate the certification and may create an unsafe situation. 

PEDs are charged using a charger dock or directly using a micro USB connection. The charger dock has a micro 
USB connection that allows charging from a mains supply, 12Vdc car supply, or a computer through a USB port. 
Tracerco recommends that only charger accessories supplied by Tracerco are used. 

Attention

: Do not attempt to replace the battery.  

 

 

Charging with the charger dock 

Charging with a micro USB connection  

During charging, an estimation of battery capacity and a lightning flash icon is displayed. When the estimated battery 
charge is greater than 95% the display shows full charge. Active warning messages are also displayed during charge. 

Attention

: PEDs do not record data while charging. 

Summary of Contents for Tracerco PED Blue


























Reviews:

No comments