Johnson Fitness T8000Pro Page 9 Service Manual Download | Manualshive

Page: 9 / 41

background image

9

Replace Right / Left side rail module procedure

If side rail LED will be not light, please replace Right / Left foot rail set, because

replace side rail module is very difficult.

Caution:

Step.1 Take off the right / left end cap

Step.2 Remove the damage side rail

Step.3 Assembly the side rail and end cap

Step.4 Connect side rail wire to right rail

wire (UP).

Step.5 Press “START” key, to run the

machine confirm the side rail LED is good.

«
...
7
8
9
10
11
...
»

Summary of Contents for T8000Pro










































Reviews:

No comments

Related manuals for T8000Pro

Cadence 800 Treadmill

Brand: Weslo Pages: 24

Brand: Healthrider Pages: 36

Brand: LA Fitness Pages: 17

Brand: York Fitness Pages: 20

Brand: Life Gear Pages: 23

Brand: Weslo Pages: 18

Brand: BH FITNESS Pages: 71

Brand: BH FITNESS Pages: 71

Brand: ProForm Pages: 19

530 HeartRateControl

Brand: ProForm Pages: 34

Brand: Dyaco Pages: 34

everlast 1654915

Brand: Dyaco Canada Pages: 43

Brand: BH FITNESS Pages: 25

Brand: D.C. Athletics Pages: 28

Brand: NordicTrack Pages: 32

Brand: Life Fitness Pages: 3

Brand: Motus Pages: 40

Brand: Motus Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands