Johnson Controls ZV Series Installation Manual Download | Manualshive

Page: 31 / 66

background image

5370939-TIM-C-0518

Johnson Controls Ducted Systems

31

If the demand for cooling from the space/return is satisfied, the
economizer output will modulate to minimum position and the
compressor outputs will be de-energized as long as their
minimum run timers have expired.

Power Exhaust

Setpoints

a. Economizer Enable ON

b. Power Exhaust Enable ON

c. Modulating Power Exhaust OFF

d. Exhaust VFD Installed OFF

e. Building Pressure Sensor Enabled OFF

f. Econo Damper Position For Exh Fan ON Percent

g. Econo Damper Position For Exh Fan OFF Percent

Inputs

No inputs are present for non-modulating power exhaust.

Outputs

a. 2-10 VDC from ECON on Economizer Expansion module

b. 24 VAC from EX-FAN to energize exhaust fan on

Economizer Expansion module

Operation

Operation details include:

a. Compares economizer output to the Economizer Damper

Position For Exhaust Fan On and OFF.

b. Energizes exhaust fan when economizer output is above

Economizer Damper Position For Exhaust Fan On.

c. De-energizes exhaust fan when economizer output is

below the Economizer Damper Position for Exhaust Fan
OFF

«
...
29
30
31
32
33
...
»

Summary of Contents for ZV Series



































































Reviews:

No comments

Related manuals for ZV Series

Brand: Unitary products group Pages: 2

Brand: York Pages: 4

Brand: sans Pages: 16

Brand: AiroDoctor Pages: 8

Brand: Zamil Pages: 20

Brand: Daikin Pages: 6

Brand: Daikin Pages: 72

Brand: Daikin Pages: 20

Brand: Daikin Pages: 44

Appliances AHM24DPH1

Brand: GE Pages: 1

Brand: Panasonic Pages: 108

Brand: Daikin Pages: 17

AIRCO BLIZZARD 1000

Brand: WTA Pages: 14

Brand: EdgeStar Pages: 23

TC 200 SPLIT Series

Brand: Gorenje Pages: 40

Brand: Carrier Pages: 12

Split Sensira R32

Brand: Daikin Pages: 208

Brand: REMKO Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands