background image

ZFR1810 Wireless Field Bus Coordinator Installation Instructions

10

Accessories

Technical Specifications      

Table 4:  Accessories (Order Separately)

Product Code 
Number

Product Description

TP-2420

Transformer, Wall Plug Mount, 120 VAC to 24 VAC, 20 VA, Class 2

WRZ-SST-120

Wireless Sensing System Tool. Requires WRZ Series Sensor to function as a site survey tool for 
ZFR1800 Wireless Field Bus System, or for WRZ-7860-0 One-to-One Room Sensing System.

Y65T31-0

1

Transformer, 120/208/240 VAC to 24 VAC, 40 VA, Class 2, Foot Mount, 20 cm (8 in.) Primary Leads 
and Secondary Screw Terminals

ZFR-USBHA-0

USB Dongle with ZFR Driver provides a wireless connection through the CCT to allow wireless 
commissioning of the wireless enabled FAC, FEC, IOM, and VMA16 controllers. The USB ZFR Dongle 
is also used with the ZFR Checkout Tool used to troubleshoot and validate ZFR wireless meshes using 
a laptop computer. 

ZFR-1810ANT-700

Replacement antenna kit for ZFR1810 Wireless Field Bus Coordinator. Includes antenna, coaxial 
cable, and mounting hardware.

1.

Additional Y60 Series Transformers are available from Johnson Controls.

ZFR1810 Wireless Field Bus Coordinator (Part 1 of 2)

Product Code Number

MS-ZFR1810-x

Power Supply Input

One of the following:

• 

24 VAC +10%/-15%, 50/60 Hz, Class 2. Transformer allowance should be 2.5 VA 
maximum, 2 VA typical. Provided through the three-position 24 V~ screw terminal 
pluggable block.

• 

15 VDC, 180 mA (7 to 18 VDC, 185 mA maximum current draw) on the FC Bus 
provided through the FC/SA BUS IN RJ-12 jack from the FC Bus Jack on a Field 
Controller or NxE supervisory engine.

Power Supply Output

15 VDC; Provided through the FC/SA BUS, FC/SA BUS OUT RJ-12 jack for external 
devices.

Addressing

DIP Switches, Field Adjustable

Wireless Band

Direct-Sequence Spread-Spectrum, 2.4 GHz ISM Bands

Transmission Power

10 mW Maximum

Transmission Range

76.2 m (250 ft)

 

Maximum Line-of-Sight 

15 m (50 ft) Recommended

Ambient Conditions

Operating:

 0 to 50°C (32 to 122°F), 5 to 95% RH, Noncondensing

Storage:

 -20 to 70°C (-4 to 158°F), 5 to 90% RH, Noncondensing

Materials

White Plastic Housing with Plenum rating per UL1995 UL94-5VB Flammability Rating

Terminations

Two spade terminals with three-position screw terminal pluggable block for 24 VAC power 
supply input.
Four spade terminals with four-position screw terminal pluggable block for RS-485 
communications.
RJ-12 IN jack for 15 VDC power supply and communications connection from an NxE or 
FEC FC Bus jack. 
RJ-12 OUT jack supplies 15 VDC and communications to BTCVT Wireless 
Commissioning Converter.

Dimensions

146 x 122 x 52 mm (5.8 x 4.8 x 2.1 in.)

Summary of Contents for ZFR1810












Reviews: