manualshive.com logo in svg

Johnson Controls YORK YV2VYH010KAR-D-X, Installation Manual

Share
Download
Johnson Controls YORK YV2VYH010KAR-D-X Installation Manual Download Page 27

25

Failure code

The lamp of the outdoor unit control PCB indicates failure code when malfunction occurs. (This 

malfunction table only applies to the follow models referred in this manual.)

Flashing

 times and

 error code

 displayed of

 outdoor unit

Error code 

displayed on 

wired controller

Failure code description

Outdoor unit defrost temp. Sensor TE circuit
Outdoor unit ambient temp. Sensor TA circuit
Compressor suction temp. Sensor TS circuit
Compressor discharge temp. Sensor TD circuit
Condenser coil temp. Sensor TC
The protocol is not match with that model
Current sensor failure
Dc fan motor failure
The current indoor unit qty is different from the qty of indoor 

units which were locked. Please refer to outdoor unit PCB 

dipswitch setting.
Main board not sure failure
Compressor discharge temp. Protection (TD)
Power module temp. Protection
High pressure switch circuit
Low pressure switch circuit
Low discharge temp. Protection
Compressor suction temp. Protection (TS)
The capacity of running indoor units is over load
Power supply over current
The communication failure with power module / not match with 

power module
Compressor over current
The communication failure with indoor units
IPM failure
IPM temperature too high
Over current in compressor frequency increasing phase (power 

module itself)

21
22
23
24
25
26
27
28

29

2A
2B
2C
2D
2E
2F
30
31
32

34

35
36
37
38

39

01
02
03
04
05
06
07
08

09

10
11
12
13
14
15
16
17
18

20

21
22
23
24

25

YV2VYH010KAR-D-X  YV2VYH015KAR-D-X  YV2VYH015KAS-D-X   YV2VYH018KAS-D-X  

Malfunction code and malfunction confirming

Summary of Contents for YORK YV2VYH010KAR-D-X

































Reviews:

No comments

Brands by name

Popular brands

Load more brands