Johnson Controls VMA1200 Series Mounting And Wiring Instruction Download Page 1

Technical Bulletin

Issue Date

July 1, 2003

© 2003 Johnson Controls, Inc.

www.johnsoncontrols.com

Code No. LIT-1162360

M-Tool Release 5.3

Mounting and Wiring VMA1200 Series Controllers

Mounting and Wiring VMA1200 Series Controllers............................2

Introduction......................................................................................................... 2

Key Concepts...................................................................................................... 3

VMA Position and Orientation ........................................................................................... 3

Determine and Set Damper Polarity ................................................................................. 3

Wiring and Cabling Precautions........................................................................................ 4

VMA Internal Schematic Diagram ..................................................................................... 6

Phone Jack Polarization.................................................................................................... 8

Detailed Procedures......................................................................................... 10

Preparing the VMA for Mounting..................................................................................... 10

Mounting the VMA........................................................................................................... 11

Setting the Damper Position ........................................................................................... 12

Wiring the VMA ............................................................................................................... 14

Connecting the L

ON

W

ORKS

 Network Bus........................................................................ 15

Summary of Contents for VMA1200 Series



















Reviews: