background image

Table5: PC address settings

Address type

Default address

Subnet Mask

255.255.255.0

Default Gateway

192.168.92.1

Configuring the router

To configure the router:

1.  In your web browser address field, enter the router IP address: 

192.168.92.68

.

2.  Use the following table as a reference when you configure the router parameters.

Table6: Router parameters

Name

Description

Device Instance

Enter a unique 22-bit decimal value (0–4,194,303). Each network device

must have a unique device instance.

Default Value = 0

Ethernet Network

Enter a unique 16-bit decimal value (0–65,535). Each BACnet network,

regardless of technology, must have a unique network number.

By retaining a value of 0, BACnet Ethernet routing is disabled.

Default Value = 0

Note: 

The Ethernet Network field represents the BACnet over

Ethernet network number. BACnet over Ethernet is a different

networking technology than BACnet/IP. Ethernet Network and

BACnet/IP Network must each have a unique BACnet network

number.

BACnet/IP UDP Port

Enter a 16-bit hexadecimal value. All BACnet/IP devices on the same

BACnet network must have the same BACnet/IP UDP port assignment.

Normally, you do not need to change this value. If you do, avoid well-

known ports that have hexadecimal addresses, such as 15, 17, or 50.

Instead, choose port numbers in the range of BAC1 through BACF.

Default Value = BAC0 (hexadecimal)

Note: 

MS-CCT and FX-CommPro BACnet identify the BACnet/IP UDP

port number in decimal format, while the BACnet router identifies

the UDP port number in hexadecimal format. The decimal number

47808 is equivalent to the hexadecimal number BAC0.

BACnet/IP Network

Enter a unique 16-bit decimal value (0–65,535). Each BACnet network,

regardless of technology, must have a unique network number.

Default Value = 1

IP Address

Enter the IP address of the router in dotted decimal format. Select a valid

address in the range from 0.0.0.1 to 255.255.255.254.

Default Value = 192.168.92.68

IP Subnet

Enter a decimal value (0–30) for the IP subnet mask. This value is the

number of bits with a 1 in the mask.

Default Value = 24

IP Gateway

Enter the default gateway for the IP stack. This value is a dotted decimal

number that ranges from 0.0.0.1 to 255.255.255.254.

Default Value = 192.168.92.1

Portable BACnet/IP to MS/TP Router Installation Instructions

6

Summary of Contents for TL-BRTRP-0











Reviews: