background image

Operating manual - ComPAC

10/56

011769 en 2020.03

Introduction

1.1.2

Definition of safety precautions used in this manual

Danger!

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious
injury.

Warning!

Indicates a potentially hazardous situation or practice which, if not avoided, will result in death or
serious injury.

Caution!

Indicates a potentially hazardous situation or practice which, if not avoided, will result in damage
to equipment and/or minor injury.

Note:

Indicates an operating procedure, practice, etc., or portion thereof, which is essential to

highlight.

1.1.3

Requirements for competent persons

Personnel working on the unit must be competent in accordance with national safety rules
and regulations relating to flammable refrigerants or according to EN 13313.

Maintenance work must be performed according to EN 378 or ISO 5149 supported by evi-
dence of appropriate training.

Assign only competent personnel instructed in safety and all machine functions to operate
or service the compressor/unit according to EN 13313.

Operators and maintenance personnel must carefully read, understand and fully comply
with all alarms and instructions.

Summary of Contents for SABROE ComPAC





























































Reviews: