manualshive.com logo in svg

Johnson Controls NAE35, Installation Manual, Page: 25 / 28

Share
Download
Johnson Controls NAE35 Installation Manual Download Page 25

Technical specifications

Table 12: NAE35 and NAE45

Power

Requirement

Dedicated nominal 24 VAC, Class 2 power supply (North America), SELV power

supply (Europe), at 50/60 Hz (20 VAC minimum to 30 VAC maximum)

Power

Consumption

25 VA maximum

Ambient

Operating

Conditions

0–50°C (32–122°F); 10–90% RH, 30°C (86°F) maximum dew point

Ambient Storage

Conditions

-40–70°C (-40–158°F); 5–95% RH, 30°C (86°F) maximum dew point

Data Protection

Battery

Supports data protection on power failure. Rechargeable NiMH battery: 3.6

VDC 500 mAh, with a typical life of 5 to 7 years at 21°C (70°F); Product Code

Number: MS-BAT1020-0

Processor

192 MHz Renesas

®

 SH4 7760 RISC processor

Memory

128 MB flash nonvolatile memory for operating system, configuration data,

and operations data storage and backup128 MB SDRAM for operations data

dynamic memory

Operating System

Release 9.0: 

Microsoft

®

 Windows Embedded CE 6.0

Release 9.0.7: 

Buildroot 2017.08.2 with Linux kernel 14.4

Note: 

The Windows Embedded OS sticker on the bottom of the network

engine permits downgrading the engine to an older 

Metasys

 release that

uses a Windows Embedded OS.

Network and

Serial Interfaces

One Ethernet port; 10/100 Mbps; 8-pin RJ-45 connector
One optically isolated RS-485 port; 9600, 19.2k, 38.4k, or 76.8k baud

(depending on protocol); with a pluggable and keyed 4-position terminal block

(FC Bus available on NAE351x-1 and NAE451x-1 models only.)
One LonWORKS port; FTT10 78 Kbps; pluggable, keyed 3-position terminal

block (LonWORKS port available on NAE352x-x and NAE452x models only;

Release 9.0 only)
One RS-232-C serial port with standard 9-pin sub-D connector that supports

standard baud rates
There is a second serial port, on models without an internal modem, that

supports an optional, user-supplied external modem.
One USB serial port with standard USB connector that supports an optional,

user-supplied external modem (Release 9.0 only)
Option: One telephone port for internal modem; up to 56 Kbps; 6-pin modular

connector (network engine models with optional internal modem have one

RS-232-C serial port only; Release 9.0 only.)

Housing

Plastic housing material: ABS + polycarbonate
UL94-5VB Protection: IP20 (IEC 60529)

Mounting

On flat surface with screws on three mounting clips or a single 35 mm DIN rail

25

NAE35/NAE45 Installation Guide

Summary of Contents for NAE35





























Reviews:

No comments