background image

M9220-GGx-3 Proportional Electric Spring Return Actuators Installation Instructions

14

Technical Specifications

M9220-GGx Proportional Electric Spring Return Actuators (Part 1 of 2)

Power Requirements

AC 24 V (AC 19.2 to 30 V) at 50/60 Hz: Class 2 (North America) or SELV 
(Europe), 15.5 VA running, 7.7 VA holding position; 
DC 24 V (DC 21.6 to 26.4 V): Class 2 (North America) or SELV 
(Europe), 6.7 W running, 2.9 W holding position

Transformer Sizing Requirements

20 VA minimum per actuator

Input Signal/Adjustment

Factory set at DC 0 to 10 V, CW Rotation with signal increase;
Selectable DC 0 (2) to 10 V or 0 (4) to 20 mA with field furnished 
500 ohm, 0.25 W minimum resistor;
Switch selectable direct or reverse action with signal increase

Control Input Impedance

Voltage Input: 100,000 ohms;
Current Input: 500 ohms with Field Furnished 500 ohm resistor

Feedback Signal

DC 0 (2) to 10 V for desired rotation range up to 90°;
Corresponds to rotation limits, 1 mA maximum

Auxiliary Switch Rating

GGC Models

Two Single-Pole, Double-Throw (SPDT), double-insulated switches with 
gold flash contacts:
AC 24 V, 50 VA Pilot Duty; 
AC 120 V, 5.8 A resistive, 1/4 hp, 275 VA Pilot Duty; 
AC 240 V, 5.0 A resistive, 1/4 hp, 275 VA Pilot Duty

Spring Return

Direction is selectable with mounting position of actuator: 
Side A, actuator face away from damper for CCW spring return; 
Side B, actuator face away from damper for CW spring return

Running and Spring Return Torque

177 lb·in (20 N·m) for a single actuator; 
354 lb·in (40 N·m) for two like models mounted in tandem
531 lb·in (60 N·m) for three like models mounted in tandem

Rotation Range

Adjustable from 30 to 90° CW or CCW with optional 
M9220-603 Adjustable Stop Kit; mechanically limited to 90°

Rotation Time

Power On 
(Running)

150 seconds for 0 to 177 lb·in (0 to 20 N·m) at all operating conditions; 
independent of load
90 seconds for 0 to 177 lb·in (0 to 20 N·m) in calibration mode or override 
mode

Power Off 
(Spring
Returning)

11 to 15 seconds for 0 to 177 lb·in (0 to 20 N·m) at room temperature; 
35 seconds maximum for 0 to 177 lb·in (0 to 20 N·m) at -22°F (-30°C)
130 seconds maximum for 0 to 177 lb·in (0 to 20 N·m) at -40°F (-40°C)

Cycles

60,000 full stroke cycles; 1,500,000 repositions

Audible Noise Rating

Power On 
(Running)

<45 dBA at 39-13/32 in. (1 m)

Power On 
(Holding)

<20 dBA at 39-13/32 in. (1 m)

Power Off 
(Spring
Returning)

<55 dBA at 39-13/32 in. (1 m)

Electrical Connections

Actuator
(All Models)

48 in. (1.2 m) halogen-free cable with 18 AWG (0.75 mm

2

) wire leads

Auxiliary 
Switches 
(GGC Models)

48 in. (1.2 m) halogen-free Cable with 18 AWG (0.75 mm

2

) wire leads

Conduit Connections

Integral connectors for 3/8 in. (10 mm) flexible metal conduit

Summary of Contents for M9220-GGx-3 series
















Reviews: