Johnson Controls M9206-DN Series Installation Instructions Download Page 5

Technical Specifications 

Product 

M9206-DNx Series Electric Spring Return Economizer Damper Actuators 

Power Requirements 

and Input Signal 

See 

AD-DME100-0

 

Direct-Mount Economizer Controller Installation Instructions 

(Part No. 24-9618-30).

 

Auxiliary Switch Rating 

DNB: 

Single-Pole, Double-Throw (SPDT), switch rated at 24 VAC, 1.5 A inductive, 3.0 A 
resistive, 50 VA maximum, Class 2 

Spring Return 

Direction is selectable with the mounting position of the actuator: 
 

CCW face of actuator away from the damper for CCW spring return; 

 

CW face of actuator away from the damper for CW spring return 

Mechanical Output 

Running Torque: 

53 lb∙in (6 N∙m) 

Rotation Range 

Adjustable from 34.5 to 90

°

 CW or CCW, mechanically limited to 93

°

±3 degrees 

Rotation Time 

Powered (On): CW (non-spring return direction): 10-40 seconds for full travel for 0 to 6 NM 
(0 to 53 lb·in) all operating conditions, 22 seconds nominal for 50% rated load. 

Powered (On): CCW (spring return direction): 20-70 seconds for full travel for 0 to 6 NM 
(0 to 53 lb·in) in all operating conditions. 

Unpowered (Off): Spring return time is 35 seconds nominal, 70 seconds maximum 

Cycles 

60,000 full stroke cycles; rated at 53 lb

∙in (6 N∙m) 

Audible Noise Rating 

55 dBA nominal at 1 m 

Electrical Connection 

Actuator: 

17 in. (0.43 m) cable with 5-pin connector 

Auxiliary Switch:  48 in. (1.2 m) cable with 18 AWG wire leads 

Mechanical Connection 

1/2 in. (13.0 mm) diameter round shaft or a 3/8 in. (10 mm) square shaft 

Enclosure 

IP20 

Ambient Conditions 

Operating: 

-25 to 140

°

F (-32 to 60

°

C); 10 to 90% RH, noncondensing 

Storage:  

-40 to 186

°

F (-40 to 86

°

C); 5 to 95% RH, noncondensing 

Dimensions (H x W x D) 

DNx: 

6.98 x 3.25 x 2.99 in. (177.29 x 82.55 x 75.95 mm) 

Shipping Weight 

3.45 lb (1.56 kg) 

Agency Compliance 

UL Listed, File E27734, CCN XAPX (US) XAPX7 (Canada) 

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these 
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication 
or misuse of its products. 

 

Building Efficiency

 

507 E. Michigan Street, Milwaukee, WI  53202 

 

 

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.  

All other marks herein are the marks of their respective owners. © 2014 Johnson Controls, Inc.

 

M9206-DNx Series Electric Spring Return Economizer Damper Actuators Installation Instructions

    5

 

Summary of Contents for M9206-DN Series






Reviews: