manualshive.com logo in svg

Johnson Controls LN-DSWSC1-0, Installation Instructions Manual, Page: 6 / 8

Share
Download
Johnson Controls LN-DSWSC1-0 Installation Instructions Manual Download Page 6

LN-Display Installation Instructions

6

The LN-Display controller also has a built-in network 
jack (1/8 in. [3.5 mm] mono male audio jack) that can 
be used to connect to the L

ON

W

ORKS

 network. This 

network jack is located on the bottom of the device 
(Figure 12).

Selecting Network Terminators

For information on selecting Network Terminators, 
refer to the

 L

ON

W

ORKS

 LN-Series Network 

Communication and Interface Guide Technical Bulletin 
(LIT-12011253)

.

Setup and Adjustments

Commissioning

To commission a device and add it to a L

ON

W

ORKS

 

network, use the device plug-in as well as the .xif and 
.apb files. 

Note:

The device commissioning instructions only 

apply when you are using a L

ON

W

ORKS

 Network 

Services (LNS®) network management tool, such as 
LN-Builder.

To obtain the necessary files:

1.

Run the installation setup to install the device 
plug-in and the latest version of the .xif and .apb 
files onto your computer. The .xif and .apb files 
install in the C:\LonWorks\Import\JCI folder.

2.

Register the plug-in on the network database. By 
doing this, you create the device template that is 
used to commission the device.

3.

Commission the device using the proper device 
template and .apb file with your network 
management tool.

Note:

If you download an improper .apb file into the 

device, you may damage the Neuron chip in your 
controller. The controller may become unusable.

Neuron ID and Service Pin

To commission a device and add it to a L

ON

W

ORKS

 

network, you need the Neuron ID of the device. There 
are two methods to obtain the Service Pin number.

To locate the Neuron ID number, perform one of the 
following procedures:

1.

Manual entry:

 The Neuron ID address and bar 

code are located on either the top panel of the 
device (surface and DIN rail models), or inside the 
casing of the device (flush mount models).

2.

Service Pin:

 Press the Service Pin on the device 

to broadcast the Neuron ID on the L

ON

W

ORKS

 

network. The Service Pin on the Scheduler is 
located on the bottom right of the device 
(Figure 12). The Display device may have multiple 
methods for broadcasting the Neuron ID over the 
network depending on the revision level of the 
actual controller. The revision number is located on 
the printed circuit board, inside the casing.

Information on Revision levels:

•

all devices with Revision 5 or later have a 
Service Pin located on the bottom of the device

•

all devices with Revision 4 or earlier have a 
Reset Pin instead of a Service Pin. (When you 
press the Reset Pin the controller performs a 
cold reset and restarts the device.)

Repair Information

If the LN-Display fails to operate within its 
specifications, replace the unit. For a replacement, 
contact the nearest Johnson Controls® representative.

!

CAUTION: Risk of Property Damage.

Do not apply power to the system before 
checking all wiring connections. Short 
circuited or improperly connected wires 
may result in permanent damage to the 
equipment.

MISE EN GARDE : Risque de dégâts 
matériels.

Ne pas mettre le système sous tension 
avant d'avoir vérifié tous les raccords de 
câblage. Des fils formant un court-circuit 
ou connectés de façon incorrecte 
risquent d'endommager 
irrémédiablement l'équipement.

Figure 12: Bottom View

Summary of Contents for LN-DSWSC1-0









Reviews:

No comments