background image

IQ Outlet is a Z-Wave Plus® cer�fied device with S2 security and SmartStart 

features. You can now add this device securely and with ease using QR code on the 

product with compa�ble gateways suppor�ng S2 and SmartStart. IQ Outlet is a 

member of the Z-Wave™ family and communicates with other Z-Wave cer�fied 

devices in a control network. It can be used to turn On or Off lamps or AC operated 

appliances as well as monitor the energy consumed. Each Z-Wave device also 

serves as a node to repeat the signal in the network, thus, extending the overall 

Z-Wave mesh wireless network range. Different types and brands of Z-Wave 

devices can be associated with IQ Outlet in your system and they will work 

together to op�mize and expand the coverage of your Z-Wave network. 

Turns ON/OFF incandescent, CFL, or LED lamps, and AC operated appliances

700 Series Z-Wave module

Energy monitoring supported

LED to indicate ON/OFF status 

Remotely or manually turns ON or OFF lights

Controls appliances up to 15A 

Z-Wave Plus Cer�fied with S2 security and SmartStart (QR code on bo�om of device) 

Grounded 3-pin AC power receptacle to enhance safety

Safety tab to secure unit to AC outlet

Compact design - does not block the 2nd AC outlet

Over-The-Air firmware upgrade available, if supported by controller

Supports Network Wide Inclusion (through a repeater), if supported by controller

Func�ons as a Z-Wave signal repeater

INTRODUCTION

FEATURES

The connected appliance can be controlled manually with a push bu�on or 

wirelessly via the so�ware from your controller.

A Z-Wave cer�fied controller is capable of se�ng up this product in your 

desired network. Once the device is added, you may assign it to a group. 

Please refer to the instruc�ons manual of your controller for details and 

procedures on how these se�ngs can be done. 

BASIC OPERATION

Step 1

! WARNING ! 

RISK OF FIRE, ELECTRICAL SHOCK & BURNS

DO NOT USE WITH MEDICAL AND LIFE SUPPORT INSTRUMENT 

No user serviceable parts are in this module

To reduce the risk of electric shock, this product has a grounding type plug that has 

a third (grounding) pin. This plug will only fit into a grounding type power outlet. 

If the plug does not fit into the outlet, contact a qualified electrician to install the 

proper outlet. Do not change the plug in any way.

The appliance connected to this Z-Wave module must not exceed 900W 

incandescent, 200W CFL/LED, ½ horsepower motor and 15A, 1800W resis�ve load.

SETUP

Step 2

Insert the module's 3-pin plug into an AC 

outlet in the same room as your gateway. 

Plug in the AC power plug of the appliance 

to the receptacle of IQ Outlet.

3. Plug IQ Outlet back into the AC outlet with the bu�on pressed

A�er 3 seconds, release the bu�on. If you see the LED blink, that means that IQ 

Outlet has been reset successfully and you may retry Step 3 in Setup to add the 

module into your network. Otherwise, please repeat the manual reset procedure.   

About the push bu�on:

There is a single bu�on on IQ Outlet for manual opera�on that: 

Manually turns the connected ligh�ng ON/OFF by pressing the bu�on. It 

func�ons as a toggle switch.

Adds (Includes) or Removes (Excludes) your IQ Outlet to/from your Z-Wave 

network. Please refer to the instruc�ons manual of your gateway or 

remote controller for detail procedures on how these ac�ons can be done.

In the event of a power failure, the device will return to the last se�ng 

a�er the power is restored (refer to Advanced Configura�on sec�on to 

change the default).

Energy Monitoring: 

This device supports energy monitoring and it is expressed in kWh and Wa�s.

IQ Outlet

User Guide

A)
B)

Manual Reset

2. Press and hold the bu�on on IQ Outlet.

Please use this procedure only when the network primary controller is missing 

or otherwise inoperable. The manual reset method is as follows:

1. Unplug IQ Outlet from the AC outlet and 

also unplug the power plug of the appliance 

from the IQ Outlet (if plugged in).

Plug In Switch

This product speaks 

with other Z-Wave 

cer�fied devices

1. Place your network controller into inclusion mode by following the controller 

manufacturer's instruc�ons.

2. When the controller is ready, single click the bu�on on the top of the IQ Outlet. 

The controller should indicate that the new device was added successfully.

3. Once IQ Outlet has been successfully added to your home network, you can 

move it to the preferred loca�on in the home.
If the controller shows it failed, repeat the procedure.

Step 3

 Inclusion/Exclusion: Add or remove the device into your network by a 

Z-Wave cer�fied controller. IQ Outlet supports the latest S2 security and SmartStart 

offered by Z-Wave cer�fied controllers. If your controller supports S2 or SmartStart, 

please refer to the user guide of the controller for detailed instruc�ons on adding or 

removing devices to/from the network. You should be able to add IQ Outlet into 

your network using the unique QR code or the DSK 5 digit pin located on the 

product or packaging. In addi�on, the device can be added or removed using the 

tradi�onal method for Z-Wave as follows:

Note: 

If 

IQ Outlet 

was previously Added (Included) in your network, rese�ng it locally 

does not mean it has been removed from your controller so�ware. If you wish to remove 

the 

IQ Outlet 

from your controller so�ware you will need to remove (Exclude) the 

module from the network by your controller. If 

IQ Outlet 

is removed from the network 

suppor�ng S2 security, the only way to add the device back into the network is using the 

QR code or the DSK code. Therefore, please store the QR code on the product as well as 

copy of the full DSK printed on the package in a safe loca�on.

Use the manual reset procedure only in the event that the network primary 

controller is lost or otherwise inoperable. 

1

2

or

Reviews: