FX-WRZSST-110 Wireless Sensing System Tool Installation Instructions
2
Canada
Installation
Transport the FX-WRZSST-110 Wireless Sensing
System Tool in the original container to minimize
vibration and shock damage to the receiver.
Verify that all the parts shipped with the receiver:
•
one FX-WRZ7850 Receiver with two magnets
attached
•
one battery pack with two magnets attached
•
two AA alkaline batteries
•
one installation instructions sheet
Do not drop the receiver or subject it to physical shock.
Mounting
To mount the receiver:
Note:
Check that the power switches on the
FX-WRZ7850 Receiver and FX-WRZ Series Sensor
are set to
OFF
before proceeding.
1.
Set the
TRANSMITTER ID
and
AREA
DIP
switches on the FX-WRZ7850 Receiver and the
FX-WRZ Series Sensor to the same address.
Refer to the
One-to-One Wireless Sensing System
Technical Bulletin (LIT-12011663)
for more details.
2.
Install the batteries into the battery pack.
3.
Connect the battery pack wire harness to the
two-pin connector located under the
TRANSMITTER ID
DIP switches on the back of
the FX-WRZ7850 Receiver.
Note:
Connecting the battery pack to the receiver
transforms the FX-WRZ7850 Receiver into the
FX-WRZSST Tool.
4.
Turn the battery pack switch to
ON
.
5.
For a One-to-One wireless room sensing system,
place the FX-WRZSST-110 Tool in the area where
the FX-WRZ7850 Receiver is to be located, and
place the FX-WRZ Series Sensor in the area
where you intend to mount the sensor.
This Class (A) digital apparatus meets all the
requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte
toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
RF Transmitters: Industry Canada Statements
The term
IC
before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
This device has been designed to operate with an
antenna having a maximum gain of 2 dB. Antenna
having a higher gain is strictly prohibited per
regulations of Industry Canada. The required
antenna impedance is 50 ohms.
To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the Equivalent Isotropically Radiated Power
(EIRP) is not more than that required for successful
communication.
Le terme « IC » précédant le numéro d'accréditation/
inscription signifie simplement que le produit est
conforme aux spécifications techniques d'Industry
Canada.
Cet appareil a été conçu pour fonctionner avec une
antenne d'un gain maximum de 2 dBi. En application
des réglementations d'Industry Canada, l'utilisation
d'une antenne de gain supérieur est strictement
interdite. L'impédance d'antenne requise est de
50 ohms.
Pour réduire les interférences radio potentielles
avec les dispositifs d'autres utilisateurs, le type
d'antenne et son gain doivent être choisis de façon à
ce que la Puissance Isotrope Rayonnée Équivalente
(PIRE) ne soit pas supérieure à la puissance
nécessaire pour une bonne communication.
IMPORTANT:
If there are other wireless mesh
networks or One-to-One wireless room sensing
systems in the area, ensure that the
PAN OFFSET
address of the FX-WRZ7850 Receiver and
FX-WRZ Series Sensor (set by the
TRANSMITTER
ID
and
AREA
DIP Switches) is different from the
PAN OFFSET
address of those wireless mesh
networks or One-to-One wireless room sensing
systems.
