background image

Table 10: FX-PCX4711-x Technical Specifications

United States:

UL Listed, File E107041, CCN PAZX, UL 916, Energy Management

Equipment

FCC Compliant to CFR47, Part 15, Subpart B, Class A

Compliance

Canada:

UL Listed, File E107041, CCN PAZX7 CAN/CSA C22.2 No.205, Signal

Equipment

Industry Canada Compliant, ICES-003

Europe:

Johnson Controls, Inc. declares that this product is in compliance with the

essential requirements and other relevant provisions of the EMC Directive.

Note:

Conducted RF Immunity within EN 61000-6-2 meets performance criteria B.

Australia and New Zealand:

RCM Mark, Australia/NZ Emissions Compliant

BACnet International:

BACnet Testing Laboratories (BTL) Protocol Revision 4

Listed BACnet Application Specific Controller (B-ASC)

The performance specifications are nominal and conform to acceptable industry standard. For application at conditions
beyond these specifications, consult the local Johnson Controls

®

office. Johnson Controls, Inc. shall not be liable

for damages resulting from misapplication or misuse of its products.

APAC Single Point of Contact:

NA/SA Single Point of Contact:

European Single Point of Contact:

JOHNSON CONTROLS

C/O CONTROLS PRODUCT MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

Johnson Controls

®

is a registered trademark of Johnson Controls, Inc.

All other marks herein are the marks of their respective owners.

©

2016 Johnson Controls, Inc.

www.johnsoncontrols.com

Published in U.S.A.

22

FX-PCX47 Expansion Input/Output Module Installation Instructions

Summary of Contents for FX-PCX47























Reviews: