manualshive.com logo in svg

Johnson Controls FX-PCV18 Series, Installation Instructions Manual, Page: 27 / 30

Share
Download
Johnson Controls FX-PCV18 Series Installation Instructions Manual Download Page 27

Table 8: FX-PCV18 Controller accessories. Order separately

Product Code Number Description

Mobile Access portal

(MAP) Gateway

To identify the appropriate product for your region, refer to the 

Mobile

Access Portal Gateway Catalog Page

 (LIT-1900869). 

1

1

NS Series Network

Sensors

Refer to the 

NS Series Network Sensors Product Bulletin (LIT-12011574)

 for

specific sensor model descriptions.

Y64T15-0

Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 92 VA, Foot

Mount, 30 in. Primary Leads and 30 in. Secondary Leads, Class 2

Y65A13-0

Transformer, 120 VAC Primary to 24 VAC Secondary, 40 VA, Foot Mount

(Y65AS), 8 in. Primary Leads and 30 in. Secondary Leads, Class 2

Y65T42-0

Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 40 VA, Hub

Mount (Y65SP+), 8 in. Primary Leads and Secondary Screw Terminals,

Class 2

Y65T31-0

Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 40 VA, Foot

Mount (Y65AR+), 8 in. Primary Leads and Secondary Screw Terminals,

Class 2

AP-TBK4FC-0

Replacement MS/TP FC Bus Terminal, 4-Position Connector, Blue, Bulk

Pack (10 pack)

AS-CBLTSTAT-0

AS-CBLTSTAT-0 Cable adapter for connection to 8-pin TE-6700 Series

sensors

AS-CBLVMA-1

Cable Adapter, 8-pin Female Socket to 6-Pin Male Jack (Bulk Pack of 10)

AS-CBLVMA-2

Cable Adapter, 8-pin Female Socket to 8-pin Male Jack with 6-Pin Female

Socket for Wireless Commissioning Converter (Bulk Pack of 10)

NS-WALLPLATE-0

Network Sensor Wall Plate (80 mm x 80 mm [3.15 in. x 3.15 in.] square),

used with an 80 mm by 80 mm (3.15 in. x 3.15 in.) network sensor and

must be mounted to a 0.6 m by 1.2 m (2 ft by 4 ft) wall box

1

The MAP Gateway serves as a replacement for the BTCVT, which is no longer available for purchase, but continues to be

supported on select controllers.

Technical specifications

Table 9: FX-PCV18 Controllers

Product Code Numbers

FX-PCV1832-1:

 Programmable VAV Box N2 Controller for cooling only

and cooling with reheat and fan control applications

FX-PCV1826-1:

 Same as above except with no differential pressure

sensor

Supply Voltage

24 VAC (nominal, 20 VAC minimum/30 VAC maximum), 50/60 Hz,

Power Supply Class 2 (North America), Safety Extra-Low Voltage

(SELV) (Europe)

Power Consumption

10 VA typical, 14 VA maximum

Note: 

The VA rating does not include any power supplied to

the peripheral devices connected to Binary Outputs (BOs) or

Configurable Outputs (COs), which can consume up to 12 VA for

each BO or CO, for a possible total consumption of an additional

60 VA (maximum).

27

FX-PCV1826/1832 Programmable VAV Box Controller Installation Instructions

Summary of Contents for FX-PCV18 Series































Reviews:

No comments