background image

Page : 

1

ELLIS SIDEBOARD

Stock Number: 87702726

Thank you for purchasing this  Ellis sideboard. Please read the instructions carefully before use to

ensure safe and satisfactory operation of this product.

John Lewis

A cross head screwdriver only should be used to assemble this Ellis sideboard, an electric drill may cause

damage to the product and is not recommended.

Please check the pack contents before attempting to assemble this product. A full checklist of components is

given in this leaflet. If any components are missing, please contact the retailer from whom you bought this

product.

This product takes approximately 

90

 

MINUTES

 to assemble with 

2 PEOPLE.

All assembly should be performed on a flat, stable, clean and soft surface.

This product is 

HEAVY

, it should be assembled as near as possible to the point of use. 

TAKE CARE

WHEN LIFTING

 to avoid personal injury and (or) damage to the product

The fitting pack contains 

SMALL ITEMS

 which should be 

KEPT AWAY FROM YOUNG CHILDREN.

IMPORTANT:

 Read these instructions for future reference..

Pre-assembly preparation

Please ensure instructions are read in full before attempting to assemble this product.

Necessary Tools

Summary of Contents for ELLIS 87702726













Reviews: