manualshive.com logo in svg

Joemeek SC2.2, User Manual

Share
Download
Joemeek SC2.2 User Manual Download Page 7

6

be bypassed. When the switch is 'in', the input audio signal goes via the 
compression circuitry and is converted to 'sum and difference' mode. This 
ensures that the centre image stays perfectly in the centre even under 
heavy compression. The sum and difference coded signal is compressed, 
and then converted back into 'left/right' format. The 'hard wired' by-pass 
switch allows instant comparison between the original uncompressed 
signal, and the compressed processed signal.

ATTACK sets the time for the compression to act. When set to 'fast' the 
attack time is slightly less than 1 millisecond. At 'slow', the attack time is 
increased to  about 15 milliseconds.

RELEASE is one of the most important and noticeable controls of the 
compressor. At minimum 'fast', the release time is less than 200 
milliseconds. the range of the control is about 5 seconds. Fast releases 
make the compression effect more noticeable and more 'urgent' sounding. 
This control reacts differently depending on the status of the 'dark' switch. In 
normal mode, the compression release is smooth and linear, in 'dark' mode, 
the release starts gently, but releases quickly as the gain approaches 
normal; this gives an even more 'urgent' type of sound and often adds an 
apparent depth to the sound.

OUTPUT GAIN controls the gain of the final output driver amplifiers. Normal 
position is marked as '0'. The control can be used to set the optimum 
volume level for driving any other equipment. The output level range is high 
(maximum output can be as high as +26dB) but the gain circuit is designed 
so that when the gain is turned down, the residual noise drops with the 
signal making an extremely quiet system.

CONNECTIONS

Inputs and outputs are balanced line level but can be operated unbalanced 
without loss of quality.
If using unbalanced circuits, it is essential to ground the unused audio 
connection, ie; pin 3 on the XLRs.
The XLR Inputs are high impedance and outputs are low impedance (as is 
normal for all good outboard equipment).

JOEMEEK

 SC2.2

 

Stereo Compressor - User's guide

Summary of Contents for SC2.2
















Reviews:

No comments

Brands by name

Popular brands

Load more brands