background image

7

c) Do not place you in the area where power tool will move if kickback.

The

rebound pushes the tool in the opposite direction to movement of the wheel in

point hooking.

d) Take special care when working corners, sharp edges etc.

Avoid twists and snaps of the accessory.

Corners, edges or sharp twists tend to

hang the rotating accessory and cause loss of control or kickback

.

e) Do not attach a saw chain, blade wood carving saw chain or toothed saw

blade.

Such blades cause frequent rebounds and control losses.

Additional safety instructions for sanding operations

Do not use sandpaper too oversized for sanding discs. Follow manufacturers'

recommendations when selecting sanding paper.

More abrasive paper extending

beyond the sanding pad presents a laceration hazard and may cause a crash,

tearing of the disc or kickback.

Do not use the sander for any purpose other than that for which it is designed.

Do not get the sander wet or use in damp or wet locations or areas where there

is condensation.

Do not use the sander where there are flammable liquids, solids or gases such

as paint solvents, etc.

Do not leave the sander operating unattended.

Do not carry the sander with your finger on the power switch.

3. MACHINE-RELATED SAFETY INSTRUCTIONS

– Harmful/toxic dust can be produced during your work (e.g. lead-containing

paint, some types of wood and metal). Contact with this dust, especially

inhaling it, can represent a hazard for operating personnel or persons in the

vicinity. Comply with the safety regulations that apply in your country. Connect

the electric power tool to a suitable extraction system.

To protect your health, wear a P2 protective mask.

Always wear protective goggles to protect against sanding hazards.

–Use a residual current protective device when metal grinding, as well as when

the operation of the power tool in a wet environment cannot be avoided. In the

event of an electric shock, the protective switch protects you against

life-threatening current through the body.

– Attention: Risk of fire! Avoid overheating the grinding material and the sander.

Always empty the dust container before taking a break. Swarf in the filter bag or

Summary of Contents for BRUSHLESS CT5650






















Reviews: