background image

ACCESSORIES & CARTON CONTENTS 

 
 

 
AVAILABLE ACCESSORIES 

 
        

WARNING:

 Use only accessories 

recommended for this cordless drill. 
Follow instructions that accompany 
accessories. Use of improper 
accessories may cause injury to the 
operator or damage to the cordless drill. 
 

Do not use any accessory unless you have 

completely read the instructions or Owner’s 
Manual for that accessory. 
 

 

Drill bits 

 

Screwdriver bits 

 
 
 
 

        

WARNING:

 If any part is missing or 

damaged, do not plug the charger into 
the power source until the missing or 
damaged part is replaced. 
 

Carefully unpack the drill. Compare against 
the “Drill Components” chart at right. 

NOTE:

 See illustration of components on 

Page 10. 

 

 

        WARNING: To avoid fire or toxic 
reaction, never use gasoline, naphtha, 
acetone, lacquer thinner or similar highly 
volatile solvents to clean the tool. 

 
 

 
CARTON CONTENTS 

– cont’d

CARTON CONTENTS 

DRILL COMPONENTS 

KEY 

DESCRIPTION 

QTY 

Drill 

Double ended 
screwdriver bits 
       #1 & #2  
      #2 &       6 mm 

 
 


Battery 

Battery charger 

Battery charger stand 

Blow moulded case 

 

Owner

’s manual 

 

 
 

 

Summary of Contents for 54-2893-4



















Reviews: