Joab EcoDrive Operation And Maintenance Manual Download Page 53 | Manualshive

Page: 53 / 73

background image

45

Shunting a Body

The operator of the hook-lift is responsible for handling it. Care must be taken to
avoid injury or damage. Before operating the hook-lift make sure that you have read
and are fully aware of the warnings in this manual and on the hook-lift.

To shunt a body from a trailer follow the procedure listed below:

1.

Make sure that there is nobody within the working area of the vehicle and the body.

2.

If the vehicle has retractable axles, make
sure that they are lowered.

3.

Start the hydraulic pump. Once the pump is
started, the pump icon will be displayed in
the CBW controller as shown.

For information regarding the starting of the
pump, refer to

"User Interface", on page 12

.

4.

Open the hydraulic-lock.

5.

Operate the extending-section so that it
fully retracts and the hook is moved out-
wards, as shown. The centre-lock will then
open.

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
51
52
53
54
55
...
»

Summary of Contents for EcoDrive










































































Reviews:

No comments

Related manuals for EcoDrive

Brand: Data Aire Pages: 28

Brand: Hanwell Pages: 34

BIO 55 MIX W-PWM 1F TRS6K

Brand: Regulus Pages: 72

Brand: hotset Pages: 2

Brand: Wachs Pages: 224

Brand: Quality Heating Pages: 15

Brand: mr. steam Pages: 4

Brand: Elko Pages: 18

Brand: Vallox Pages: 16

Brand: FY-TECH Pages: 19

Brand: Mantracourt Pages: 24

Lumina LU20S-DNW

Brand: Leviton Pages: 3

Brand: PRO LIFTS Pages: 28

Brand: BFT Pages: 23

Brand: ARITCO Pages: 85

Brand: Kongsberg Pages: 34

Brand: Whirlwind Pages: 2

Brand: JVC Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands