Joab EcoDrive LA Operation And Maintenance Manual Download Page 57 | Manualshive

Page: 57 / 89

background image

49

Tipping a Body

The operator of the hook-lift is responsible for handling it. Care must be taken to
avoid injury or damage. Before operating the hook-lift make sure that you have read
and are fully aware of the warnings in this manual and on the hook-lift.

To tip a body follow the procedure listed below:

1.

Make sure that there is nobody within the working area of the vehicle and the body.

2.

If the vehicle is fitted with an extendable underrun - retract it. Refer to

"Extendable Under-

run Protection", on page 32

.

3.

Make sure that the vehicle is on a level and firm surface.

Failure to do so, can lead to the vehicle being unevenly loaded and tipping over.
If the vehicle leans two or more degrees there is a risk that it will tip over.

4.

If the vehicle has retractable axles, make
sure that they are lowered before tipping.

5.

Start the hydraulic pump. Once the pump
is started, the pump icon will be displayed
in the CBW controller as shown.

For information regarding the starting of
the pump, refer to

"User Interface", on

EcoDrive 2.0 manual: 1021970 Edition 1 | 2022-02-04

«
...
55
56
57
58
59
...
»

Summary of Contents for EcoDrive LA


























































































Reviews:

No comments

Related manuals for EcoDrive LA

Brand: R. Beck Maschinenbau Pages: 35

Brand: Radionics Pages: 14

Brand: HIMA Pages: 58

PLATINUM PS-9003

Brand: HydroQuip Pages: 24

Brand: T&R Pages: 12

INCA STD 13-16-19

Brand: M.J. MALLIS GROUP Pages: 28

Brand: National Instruments Pages: 9

Brand: Clarke Pages: 16

Brand: Lincoln Electric Pages: 23

Hammerfall DIGI9652

Brand: RME Audio Pages: 22

Brand: M-system Pages: 10

Brand: King Tony Pages: 18

POWER FEED 10 ROBOTIC K1780-1

Brand: Lincoln Electric Pages: 29

Brand: National Instruments Pages: 14

FieldPoint FP-DI-330

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 10

FIELDPOINT FP-PWM-520

Brand: National Instruments Pages: 19

Brand: Zepro Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands