Jntech JNP22KH User Manual Download Page 65

Page: 65 / 90

ENTER

UP/DOWN

ENTER

Pin                  0W
R-Mode      MPPT
Iin                    0A
Vin                   0V
Iaout                0A
Fout          0.00Hz
Run/Stop      Stop
D_Mode       Auto
OF-F               On

RunInfo
InverterInfo
MotorCtrlPara
Statistic
Settings
Fault Inquiry
ESC

RunInfo

RunInfo
InverterInfo
MotorCtrlPara
Statistic
Settings
Fault Inquiry
ESC

Statistic

RunT_D     60min
RunT_T           1h
E-Day         0kWh
E-Tot          0kWh
ESC

ESC

RunInfo
InverterInfo
MotorCtrlPara
Statistic
Settings
Fault Inquiry
ESC

Statistic

Figure8-9 Statistic data inquiry procedure

Table8-8 Detailed statistic data

Statistic

Explain

RunT-D

Inverter daily running duration. This figure will be reset when

recharged.

RunT-T

Accumulative running duration. This figure can be reset manually.

Please refer to

“8.3.3Statistical Data Clear”

E-Day

Daily power inverted. This figure will be reset when recharged.

E-Tot

Accumulative power inverted, can b e reset manually. Please refer

“8.3.3Statistical Data Clear”

ESC

Return to the previous menu

8.3.5 Parameter Setting

Settings, set the parameter, please refer to the figure below.

Summary of Contents for JNP22KH



























































































Search results

Summary of Contents for JNP22KH

Reviews:

Related manuals for JNP22KH

Brands by name

Popular brands

Jntech JNP22KH, User Manual

Search results

Summary of Contents for JNP22KH

Reviews:

Related manuals for JNP22KH

Brands by name

Popular brands